Author: Site Editor Publish Time: 18-05-2023 Origin: Site
Since the special oil for the planetary reducer may deteriorate after the equipment has been in operation for a long time, which will seriously affect the use of the equipment, and more seriously, it may cause damage to the equipment and reduce the use efficiency. Therefore, we should treat the oil according to the requirements of the planetary reducer The oil quality of the equipment is checked regularly to ensure the normal use of the equipment.
In fact, the use effect of the planetary reducer has a lot to do with its oil quality. You must not ignore the inspection of the oil quality during use.
So, how should the oil of the planetary reducer be checked?The following Bapman Industrial Technology details its specific methods:
1. The lubricating grease of the reducer will be mildewed due to various reasons within a period of time after use, so the lubricating grease should be checked every quarter;
2. When checking the oil, first disconnect the switching power supply, wait for the reducer to turn on after water cooling, and place a non-porous oil receiving plate under the oil filling foot of the reducer, then open the oil level oil foot bolt and add some oil Add some oil to the foot bolts and ventilator, and then wait for the compressor lubricating oil to be completely discharged before reinstalling the oil and oil foot bolts and adding new grease;
3. After the lubricating oil of the compressor exceeds the specified amount according to the oil quantity bolts, tighten the oil quantity bolts and the ventilator;
4. Check whether the oil sample taken on the reducer is turbid oil. If it is, the lubricating oil on the reducer needs to be replaced immediately; the poor quality of the lubricating oil will naturally affect the actual effect of the reducer operation. To maintain the condition of the lubricating oil of the reducer, the reducer cleaning and maintenance machine adopts the original oil supply and drainage system software of the reducer, and timely checks the operation of the reducer, and timely disassembles and adjusts.
Inspection items for oil quality of planetary reducer
1. Cut off the power supply, wait for the planetary reducer to cool down, put the oil pan under the oil drain bolt, open the oil level bolt, the oil drain bolt and the ventilation valve start to drain the oil, wait until all the oil is discharged, reinstall the oil drain bolt, and then inject new of lubricating oil.
2. The brand and type of lubricating oil to be replaced should be consistent with the original lubricating oil, oil quantity and installation position. After the oil level bolts observe that the oil reaches the specified value, tighten the oil level bolts and breather.
Gearbox Housing Casting Lead Time: Pour Weight, Pattern Slots, 2027 Windows
Gearbox Shaft Seal Selection: Lip, Labyrinth or Cassette for Wet Duty
What methods can be used to avoid failure of the internal gear transmission system of CJY reducer?
What impact will a gear transmission system failure have on the CJY reducer?
Gearbox Market 2027: Retrofit Demand in Southeast Asian Palm Oil Mills
If the gear gap of the reducer is too large or too small, what efficiency problems will it cause?
How to adjust and repair the gear backlash of the reducer if it is too large or too small?
How to carry out dynamic inspection after FAF98-4KW-140-M4 gear reducer is installed
How to deal with abnormal vibration of WPDKS80-60 worm gear reducer under low load
What are the maintenance points for ZDY250-3.55-II hard tooth surface reducer in food plants?
How to perform daily inspection of the sealing system of ZDY315-4.5-I hardened reducer?
What is the clearance standard of P series planetary reducer under different working conditions?
How to choose the P series planetary reducer suitable for your equipment
How to judge the degree of breakage of ZLYJ series reducer gears by listening to the sound
What are the common causes of failure of NGW102-6 planetary reducer bearing components?
What are the repair methods after the NGW81-25 planetary reducer bearing assembly fails?
How to judge whether there is a problem with the internal transmission pair of WP series reducer
What may be the causes of load fluctuations of WP series worm gear reducer?
Gearbox Breather Selection: Dust Caps, Desiccant Dryers and Pressure Balance
Gearbox Price Trends 2027: EU CBAM and the Steel Cost Pass-Through
Gearbox Oil Change Interval: Hours, Oil Tests and Top-Up Rules