Author: Site Editor Publish Time: 05-11-2026 Origin: Site
The reducer sample is marked with a rated torque, and if it matches, place an order. This approach is sufficient in most cases, but once you encounter 'the torque is not exceeded, but the gear is broken,' or the lifespan of two machines with the same torque is several times different, it becomes unclear. Whether the gear pair can withstand it depends on the load-carrying capacity check, not the torque number itself. According to the GB/T 3480 series (equivalent to ISO 6336) and GB/T 10063-1988 'Simplified Calculation Method for the Load Capacity of General Mechanical Involute Cylindrical Gears', this article goes through the complete calibration of a set of reducer gears, and provides formulas, parameter value bases and troubleshooting steps that can be directly applied.
The main failures of gear transmission are tooth surface pitting and tooth root fracture. The two correspond to two different calculation formulas, which need to be checked separately: pitting corrosion looks at the tooth surface contact stress σ H , and More importantly, the influencing factors of the two do not overlap - the contact stress mainly changes with the pitch circle diameter and tooth width, and the bending stress mainly changes with the modulus. This determines which type of failure can be saved by changing a parameter.broken teeth look at the tooth root bending stress σ F.
Failure mode | site of occurrence | control stress | Main influencing factors | On-site signs | Directions for improvement |
|---|---|---|---|---|---|
Tooth surface pitting corrosion | Near the tooth surface pitch line | Contact stress σ H | Graduation circle diameter d 1, tooth width b, tooth surface hardness, lubricating oil | Tooth surface pitting, shallow peeling, accompanied by noise and temperature rise | Enlarged diameter, hardened tooth surface, improved lubrication |
Broken tooth root | Tooth root fillet | Bending stress σ F | Module m, tooth profile coefficient Y Fa , load impact, overload | Broken teeth and chipped teeth mostly occur suddenly | Increase module number, peak load limiting, and improve accuracy |
The tooth shape and force mechanism of the cycloidal pinwheel reducer, worm gear reducer and gear reducer motor are different, and the formula of the involute cylindrical gear cannot be directly applied: the cycloid pinwheel belongs to the meshing with small tooth difference and multiple teeth, and needs to be assessed according to the technical conditions of GB/T 36491-2018. The module and basic parameters of the worm gear are according to GB/T 10085-2018, GB/T 10088-2018. Execution, the cylindrical gear part in the gear reduction motor is consistent with the algorithm in this article.
The calculation example takes a high-speed stage of a two-stage cylindrical gear reducer with an input of 5.5 kW. All parameters are listed, making it easy to replace each item with your own working conditions.
project | symbol | value | Basis and explanation |
|---|---|---|---|
Input power | P1 | 5.5kW | The setting value of the calculation example should actually be the measured shaft power. |
input speed | n1 | 1450 r/min | 4-pole asynchronous motor rated speed |
Number of teeth | z 1 /z2 | 19/57 | Speed ratio u = 3, the number of teeth of the two gears is relatively prime |
Modulus | m | 3mm | Taken from GB/T 1357-2008 standard module series |
Tooth width | b | 40mm | Tooth width coefficient ψ d = b/d 1 = 0.70 |
Pinion torque | T1 | 36.22N·m | T 1 = 9550·P 1/n1 |
load factor | K | 1.664 | K A 1.25 × K V 1.10 × K Hα 1.10 × K Hβ1.10 |
elastic coefficient | Z E | 189.8 √MPa | Steel paired with steel |
Node area coefficient | Z H | 2.5 | Standard straight teeth, pressure angle α = 20° |
Coincidence coefficient | Z ε / Y ε | 0.883/0.702 | End surface coincidence ε α = 1.66 |
contact fatigue limit | σ Hlim | 1500MPa | 20CrMnTi carburizing and quenching HRC 58~62, MQ grade material quality |
bending fatigue limit | σ Flim | 430MPa | Same material, same quality level as above |
safety factor | S Hmin /S Fmin | 1.2/1.4 | GB/T 10063-1988 recommends S Fmin = 1.4 |
Pinion pitch circle diameter d 1 = m·z 1 = 57 mm, center distance a = 114 mm, pitch circle tangential force F t = 2T 1/d 1 = 1271 N, circumferential speed v = πd 1n 1/60000 = 4.33 m/s.
The contact stress is calculated as σ H = Z H ·Z E ·Z ε ·√(2·K·T 1·(u+1) / (b·d 12·u)), and the numerical value is σ H = 2.5 × 189.8 × 0.883 × √(2 × 1.664 × 36224 × 4 ÷ (40 × 57 2 × 3)) = 466 MPa. Allowable contact stress [σ H ] = σ Hlim /S Hmin = 1500 ÷ 1.2 = 1250 MPa, contact safety factor S H = 1250 ÷ 466 = 2.68, which meets the requirements.
If the design direction is reversed, the lower limit of the graduation circle diameter d = 29.5 mm under the same conditions when ψ d = 0.70 is taken 1 , indicating that the contact strength margin of this reducer is wide, and the marginal constraint will fall on the bending strength.
The bending stress is calculated as σ F = 2·K·T 1·Y Fa ·Y Sa ·Y ε / (b·m²·z 1). When z 1 = 19, look up the table and get the tooth profile coefficient Y Fa = 2.85, the stress correction coefficient Y Sa = 1.54, and substitute it into the small gear to get σ F1 = 54.3 MPa; 2 when the big gear z = 57, get Y Fa = 2.288, Y Sa = 1.722, and get σ F2 = 48.7 MPa. The allowable bending stress [σ F ] = 430 ÷ 1.4 = 307 MPa, the bending safety factors S F1 = 307 ÷ 54.3 = 5.66, S F2 = 307 ÷ 48.7 = 6.30, also meet the requirements.
If the tooth surface material with the same geometric dimensions (m = 3, b = 40) is replaced by 45 steel quenched and tempered (soft tooth surface, ML grade is σ Hlim = 490 MPa, σ Flim = 190 MPa), the contact safety factor immediately drops to 490 ÷ 1.2 ÷ 466 = 0.88, which is less than 1 and does not meet the requirements. This is the dividing line between hard tooth surface and soft tooth surface in terms of load-bearing capacity: the hard tooth surface reducer can carry a considerable amount more load under the same volume, relying on the tooth surface hardness and contact fatigue limit, rather than increasing the torque.
Keeping the input conditions, number of teeth, material and safety factor unchanged, and only changing the module and tooth width, you can see that the directions of the two stresses are completely different.
plan | Modulus m/mm | Tooth width b/mm | Center distance a/mm | σH / MPa | S H | σ F1 /MPa | SF1 |
|---|---|---|---|---|---|---|---|
A | 2.5 | 35 | 95 | 598 | 2.09 | 89.3 | 3.44 |
B | 3.0 | 40 | 114 | 466 | 2.68 | 54.3 | 5.66 |
C | 3.5 | 45 | 133 | 377 | 3.32 | 35.4 | 8.67 |
D | 4.0 | 50 | 152 | 313 | 4.00 | 24.4 | 12.58 |
Three reading points: First, when the modulus increases from 2.5 to 4, the bending safety factor increases by about 3.7 times, but the contact safety factor only increases from 2.09 to 4.00, and the bending strength is more sensitive to the modulus; second, when the tooth width is increased, the two stresses are reduced, but when the tooth width coefficient ψ d is too large, the load distribution becomes worse, and K Hβ will rise in the opposite direction, and the gain outweighs the gain; third, the safety factor obtained by increasing the modulus under low power conditions is often not used, plan A. Already satisfied, solution B is more balanced between volume and margin.
step | do what | Criteria and error-prone points |
|---|---|---|
1 Confirm input | Check and measure shaft power, speed, start and stop frequency, and impact characteristics | Do not use the motor nameplate power directly as shaft power. |
2 Fixed load factor | Take K A , K V , K Hα , K Hβ according to the impact level | Taking K to be too small is the most common miscalculation. Most of the "torque is enough but bad teeth" are caused by this. |
3 Fixed tooth surface plan | The hard tooth surface is carburized, quenched and ground. The accuracy level is selected according to grades 1 to 11 of GB/T 10095.1-2022. | Accuracy grade and tooth surface roughness jointly affect the dynamic load coefficient K V |
4 Double check | Calculate σ H and σ F respectively and compare them with the allowable values. | Both must be passed. Only looking at the contact stress will miss the risk of broken teeth. |
5 On-site pushback | Check the load and lubrication for pitting on the tooth surface, and check the modulus and impact overload for broken teeth. | Cycloidal pinwheel and worm gear models shall be reviewed according to respective standards. |
It should be emphasized that the nominal load and coefficient values are used for calibration, but actual failures are often triggered by instantaneous overloads that exceed expectations - blocked rotor, material jam, soft foot, and tooth mismatch will all make the actual load higher than the nominal value. Therefore, the safety factor set aside by Selection is essentially a margin for these working conditions that cannot be completely predicted, and is not a conservative waste.
The accuracy of the reducer Selection ultimately depends on the depth of understanding of the load-bearing capacity. Matching the torque only means that the parameters are matched, and passing the strength check means that the machine can handle it. After mastering the two criteria of σ H and σ F , the rated torque on the sample changes from 'a found number' to 'an engineering conclusion that can be reversed, recalculated, and questioned.' Only when problems are encountered can there be a direction for troubleshooting. Hangzhou Weigao Transmission provides product lines such as hard tooth surface reducers, 、cycloid pinwheel reducers, 、worm gear reducers , and gear reduction motors . We can conduct load capacity review and consultation based on actual measured working conditions.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?