Author: Site Editor Publish Time: 17-11-2026 Origin: Site
1. Abnormal meshing of gear system
There were residual burrs and bumps in the gear tooth surface processing, which directly caused metal scraping and abnormal noise in the early stage of trial operation.
The tooth side clearance was not calibrated during assembly and exceeded the standard range of 0.12~0.15mm for this model, resulting in impact sounds from the meshing.
The axial positioning of the gear fails, axial movement occurs, and the tooth surface edges are in partial contact, causing periodic abnormal noise.
The center distance of the gear pair is assembled incorrectly, causing the meshing marks to be skewed and causing low-frequency buzzing during operation.
2. Abnormal bearing assembly and status
The clearance is not adjusted when the new bearing is installed. If it is too large, it will cause abnormal noise, and if it is too small, it will cause a dull friction sound.
The bearing raceways and rolling elements have factory anti-rust grease residue or slight bumps, and they make rustling sounds during trial operation.
The preload force of the tapered roller bearing is improperly set, and uneven friction resistance causes intermittent abnormal noise during operation.
The inner and outer rings of the bearing are too loosely matched with the shaft and box holes, causing circling, accompanied by low-frequency rumble.
3. Lubrication system adaptation issues
The oil level was filled incorrectly before the trial run. It was lower than 1/3 of the oil window, resulting in local dry friction of the gears and bearings.
The viscosity of the lubricating oil Selection is too low and cannot form an effective pressure-bearing oil film on the surface of the soft tooth surface gear.
Impurities such as molding sand and metal chips remain inside the box, which are mixed with oil and scratch the tooth surface to produce abnormal noise.
The assembly of the lubricating oil return tank is misaligned, and some meshing parts cannot receive sufficient oil supply, causing local friction sounds.
4. Assembly accuracy deviation of the whole machine
The alignment of the couplings between the input shaft and the motor, and the output shaft and the working machine exceeds the standard, causing periodic vibration and abnormal noise.
When closing the boxes, the box positioning pins were not installed and the bolts on the joint surfaces were tightened in the wrong order, resulting in misalignment of the shafting holes.
The anchor bolts were not tightened step by step according to the specified torque, causing slight displacement of the machine body during operation, causing resonance and abnormal noise.
The assembly of the input shaft end cover and bearing gland is skewed, interfering with the operation of the shaft and producing irregular friction sounds.
5. Problems with cabinet and accessory parts
The box was slightly impacted and deformed during transportation, the parallelism of the shaft system was extremely poor, and the gear meshing was unbalanced and made abnormal noise.
Anti-rust paint flakes and welding slag remaining on the inner wall of the box fall off, and get stuck in the tooth gaps after operation, causing impact sounds.
The breathing valve was not opened at the factory, and the pressure inside the box increased rapidly with the temperature rise during the trial operation, destroying the lubrication state and causing abnormal noise.
The locking disk and connecting key on the output shaft are not locked, and there is relative sliding during transmission, resulting in a clicking sound.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?