Author: Site Editor Publish Time: 17-11-2026 Origin: Site
1. Working condition separation test (distinguish between internal and external faults)
First, by changing the operating status, determine whether the sound comes from the inside of the reducer or the external connection:
Comparison between no-load and loaded: Take off the load and only let the motor drive the reducer to run without load. If the noise disappears when no-load, it means that the fault is at the load end or coupling (such as loose coupling, load eccentricity); if the noise still exists when no-load, it is most likely an internal problem of the reducer (gears, bearings, lubrication).
Variable speed test: gradually adjust the motor speed. If the noise frequency accelerates synchronously with the rotational speed, it is mostly due to gear or bearing failure; if the noise suddenly amplifies at a specific rotational speed and then weakens after deviation, it is determined to be a resonance problem (insufficient rigidity of the installation base or concentricity deviation).
2. Listening to position identification and auxiliary detection (locking specific components)
Use a long screwdriver handle or an industrial stethoscope and attach it to different parts of the reducer for listening comparison:
At the input/output shaft bearing seat: If you hear continuous "rustling", "grunting" or high-frequency squealing, and the position is fixed at the bearing seat, it is usually due to bearing wear, improper clearance or lubrication failure.
Middle part of the gear box (gear meshing area): If you hear periodic "clicks", "clicks" or metal friction sounds, and the rhythm corresponds to the gear rotation frequency, it is mostly due to improper gear meshing clearance, tooth surface pitting or broken teeth.
Auxiliary temperature measurement: Use an infrared thermometer to measure the shell. If the temperature of a certain bearing seat is abnormally high (such as >60°C after 10 minutes of no-loading) and accompanied by abnormal noise, the bearing failure at that location can basically be locked out.
3. External installation and lubrication inspection
A large part of the abnormal noise during the trial operation of the ZQ reducer comes from the installation and lubrication details:
Installation and alignment: Check whether the anchor bolts are loose and whether the coaxiality of the motor and reducer meets the standard. Excessive concentricity deviation will cause uneven gear meshing and produce periodic noise.
Lubrication status: Check whether the oil level is at the center line of the scale and whether the oil has deteriorated or been mixed with impurities. Insufficient oil will cause sharp friction sounds from dry grinding of the gears, while too much oil may cause violent churning sounds and heat generation.
4. Stop the machine and open the cover for inspection (final confirmation)
If the external inspection fails, you need to shut down the machine and cut off the power, then open the observation hole or end cover for internal confirmation:
Inspect the gears: Observe the tooth surfaces for spalling, pitting, and metal debris. If you suspect a meshing clearance problem, you can use the lead pressure method to measure the actual backlash to determine whether it exceeds the standard range.
Check the bearing: manually rotate the inner ring of the bearing to feel if there is any jamming, abnormal noise or excessive clearance.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?