WeiGao Transmission
Email: sales@wgt.net.cn
Language
通栏图2
tonglantu.jpg
Home / News / How to determine the tooth profile code of worm gear reducer: ZA, ZI, ZN, ZK, ZC Selection comparison and calculation example - Hangzhou Weigao Transmission

How to determine the tooth profile code of worm gear reducer: ZA, ZI, ZN, ZK, ZC Selection comparison and calculation example - Hangzhou Weigao Transmission

Author: Site Editor     Publish Time: 13-11-2026      Origin: Site

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

On the drawings of worm gear reducers, in addition to the model, center distance, module, and number of teeth, there are often symbols with two letters and a number, such as ZA2, ZK1, and ZC1. It marks the tooth profile type of the worm: what tool is used to process the worm, what kind of hob is used to cut the worm gear, and whether the tooth surface can be hardened and ground, are all determined by it, which in turn determines efficiency, load-bearing and accuracy levels. For the same center distance and speed ratio, if you change the tooth profile code, the difference in output torque and case temperature rise may be greater than changing a motor.

1. What do the five tooth shape codes correspond to?

1.1 Code meaning and processing method

GB/T 10085-2018 "Basic Parameters of Cylindrical Worm Transmission" covers five tooth shapes: ZA, ZI, ZN, ZK, and ZC. Among them, ZI (involute worm) and ZK (cone-enveloping cylindrical worm) are the preferred tooth shapes recommended by the standard.

Tooth shape code

Tooth profile type and section

Processing method

Transmission efficiency eta

Carrying capacity comparison

ZA

Archimedes worm, straight tooth profile in the axis plane

Turning, soft tooth surface

0.50~0.80 (0.40~0.45 when self-locking)

1

ZN

Normal straight profile worm, straight tooth profile in the normal plane

Turning or milling, grindable

Up to 0.90

1

ZI

Involute worm, end face is involute

Surface grinding wheel grinding, hard tooth surface

Up to 0.90

1

ZK

Conical surface enveloping cylindrical worm

Conical grinding wheel grinding, hard tooth surface

Up to 0.90

1

ZC

Arc cylindrical worm

Arc edge or torus grinding wheel grinding

0.65~0.95

1.5~2

1.2 The difference between efficiency and carrying capacity

The load-carrying capacity of ordinary cylindrical worms is 1. The textbook gives 1.5~2 times for ZC arc teeth, and other textbooks write 1.5~2.5 times. ZA has low efficiency and rapid tooth surface wear, and is only suitable for occasions with a small number of heads and small loads; ZI and ZK can be hardened and ground, with improved accuracy and load-bearing, and are widely used; ZC relies on the concave and convex arc tooth profile to form an oil film, taking into account both load-bearing and efficiency, but the tool investment is higher.

2. How do the basic tooth profile parameters change with the code number?

2.1 A set of parameters for ordinary cylindrical worms

The basic tooth profile of ordinary cylindrical worms (ZA, ZN, ZI, ZK) is specified by GB/T 10087-2018 'Basic Tooth Profile of Cylindrical Worms': tooth addendum height ha = 1m, working tooth height h′ = 2m (short tooth ha = 0.8m), axial tooth pitch px = πm and the tooth thickness on the center line is equal to the tooth slot width, and the top clearance c = 0.2m (0.15m~0.35m is available), tooth root fillet radius ρ f = 0.3m (0.2m~0.4m is available), and tooth tip rounding is not greater than 0.2m. The tooth profile angle is uniformly 20°, and the value cross-sections are different: ZA takes the axial direction α x , ZN and ZI take the normal direction α n , and ZK takes the tapered tool production angle α 0. When the lead angle γ > 30° in power transmission, the tooth profile angle is allowed to increase to 25°, and in indexing transmission, it is allowed to decrease to 15° or 12°.

2.2 There is another set of arc tooth ZC

ZC arc teeth have their own parameters. Taking the ZC1 tooth profile with annular envelope as an example: arc radius of grinding wheel shaft section ρ = (5.5~6.0)m, shape angle α 0 = 23°±0.5°, top clearance of about 0.16m, and axial tooth thickness of only 0.4πm.

2.3 Compare two sets of parameters side by side

Geometric parameters

Ordinary cylindrical worm (ZA/ZN/ZI/ZK)

Arc cylindrical worm (ZC1 tooth profile)

Tooth tip height ha 1(mm)

5.0 (ha* = 1, short tooth 0.8m)

5.0 (z 1 = 2 is not greater than 3)

Head clearance c (mm)

1.0 (0.2m)

0.80 (about 0.16m)

Tooth root height hf 1(mm)

6.0

5.80 (1.16m)

Addendum circle da 1(mm)

60.0

60.0

Tooth root circle df 1(mm)

38.0

38.40

Axial tooth thickness sx 1(mm)

7.8540 (0.5πm)

6.2832 (0.4πm)

Normal tooth thickness sn 1(mm)

7.7015

6.1612

Worm gear root circle df 2(mm)

188.0

188.40

Worm gear tooth root arc radius R 1(mm)

31.0

30.80

Tooth angle

20° (ZA axis α x , other normal directions α n or shape angle α 0)

Formation angle 23°±0.5°

The ZC column in the table is calculated according to the ZC1 tooth profile. Worm gear pairs with different tooth shape codes cannot be interchanged. The worm gear tooth surface must be conjugate with the worm tooth profile, and the hob must be prepared according to the worm parameters of this tooth profile. ZA worms and ZI worm gears will cause contact area deviation. When replacing accessories, the worm and worm gear should be replaced in pairs. Replacing only one will cause contact spots to deviate and cause local overload.

3. Calculation example: Change the tooth shape code, what is the difference between torque and temperature rise?

3.1 Parameters and pairing calculations

Take a worm gear reducer under normal working conditions: input power P 1 = 5.5 kW, input speed n 1 = 1450 r/min, speed ratio i = 20. According to GB/T 10088-2018, take the module m = 5 mm, the diameter of the worm indexing circle d 1 = 50 mm (priority series matching), the diameter coefficient q = d 1/m = 10.0; take z 1 = 2 heads, then z 2 = z 1i = 40, and the center distance a = 0.5m (q + z 2) = 0.5×5×(10 + 40) = 125.0 mm, within the recommended center distance sequence of GB/T 10085-2018. Lead angle γ = arctan(z 1/q) = arctan(2/10) = 11.3099°, that is, 11°18′35.8″, output speed n 2 = 72.50 r/min, worm gear graduation circle d 2 = 200.0 mm.

3.2 Efficiency conversion torque, heat generation and heat dissipation area

Substituting the efficiency according to the tooth shape code: output torque T 2 = 9550P 1iη/n 1 = 724.48×η, heating power P s = P 1(1 − η). The heat dissipation area is based on the thermal balance diameter: A ≥ 1000P s /(K t ·([t] p − t 0)), assuming good ventilation K t = 14, allowable temperature [t] p = 70 ℃, and ambient temperature 20 ℃.

Tooth plan

Efficiency η

Output torque T 2(N·m)

Heating power P s (kW)

Required heat dissipation area A (m²)

ZA turning soft tooth surface

0.50 ~ 0.80

362.2 ~ 579.6

2.750 ~ 1.100

3.929 ~ 1.571

ZI / ZN / ZK grinding hard tooth surface

Take the reachable value 0.90

652.0

0.550

0.786

ZC arc tooth

0.65 ~ 0.95

470.9 ~ 688.3

1.925 ~ 0.275

2.750 ~ 0.393

With the same 5.5 kW input and 20:1 speed ratio, the output torque of the hard tooth surface grinding solution is 289.8 N·m higher than the ZA soft tooth surface efficiency lower limit; when the ZA efficiency is 0.50, the required heat dissipation area is 3.929 m², which is approximately 10 times the 0.393 m² when the ZC efficiency upper limit is 0.95. Textbook comparison conclusion: Under the same conditions, when the transmission ratio i is between 8 and 50, the efficiency of the arc cylindrical worm is 3% to 9% higher than that of the ordinary cylindrical worm. In this example, the lead angle 11.3099° is much larger than the self-locking limit of 3°30′, and does not constitute a self-locking condition.

4. Selection Steps to check with arrival

4.1 Five steps Selection and check the arrival

  1. First, determine the tooth shape categories according to the working conditions. For heavy loads, high speeds, and precision requirements, choose ZI or ZK that can be hardened and ground; if the concentric distance requires a higher load capacity, choose ZC arc teeth; with a small number of heads, a small load, or self-locking is required, consider ZA.

  2. Then set the parameters according to GB/T 10085-2018. The module and indexing circle diameter are matched according to the priority series of GB/T 10088-2018, the center distance is taken from the recommended sequence, and the speed ratio is preferably 10, 20, 40, and 80.

  3. Then check the tooth profile parameters of the drawing. Ordinary cylindrical worms are calibrated according to GB/T 10087-2018 ha, c, ρ f and tooth profile angle; ZC must separately calibrate the tooth tip circle diameter and tooth root circle diameter, and ordinary formulas cannot be applied.

  4. Then do a temperature rise check according to the efficiency range. Take the upper and lower efficiency limits of the tooth profile code to calculate P s and heat dissipation area. For continuous heavy-load conditions, the upper limit efficiency is used to calculate heat generation, and the upper limit efficiency is used to calculate load. The calculation of the load-bearing capacity can be based on GB/Z 115-2025 'Calculation of the Load-bearing Capacity of Gear and Worm Pairs'. This document is applicable to situations where the tooth surface sliding speed v g is not greater than 25 m/s and the coincidence degree is greater than 2.1, and the center distance is not less than 50 mm.

  5. Finalize the accuracy level and review upon arrival. The accuracy is implemented in accordance with GB/T 10089-2018. The standard stipulates 12 accuracy levels, with level 1 being the highest and level 12 being the lowest, divided into three tolerance groups; the ratio of tolerance levels between adjacent levels is 1.4 (levels 1 to 9) and 1.6 (below level 9). From level 8 to level 6, the tolerance is relaxed by 1.96 times, and from level 5 to level 5, the tolerance is relaxed by 2.744 times. When the steel worm is matched with a worm gear made of soft material, the worm can be of a higher grade and the worm gear can be of a lower grade. Upon arrival, check the nameplate, center distance and user-specified parameters in accordance with GB/T 19935-2025; Article 6.3 of this standard stipulates that the worm gear tooth profile is determined by the manufacturer or negotiated with the manufacturer. Therefore, the tooth profile code, module, graduation circle diameter, rotation direction and number of heads must be written into the technical agreement and checked item by item upon arrival.

4.2 Standard version change rhythm

GB/T 10086-2026 "Cylindrical Worm, Worm Gear Code, Basic Tooth Profile and Pattern Requirements" was released on October 30, 2026, and will be implemented on May 1, 2027. It will completely replace GB/T 10086-2018, GB/T 10087-2018 and GB/T 12760-2018, which combines the code name, basic tooth profile and drawing requirements into one document; the revision plan of GB/T 10085-2018 and GB/T 10089-2018 has also entered the approval stage. It is recommended to clearly indicate the tooth profile code and standard version number in the newly signed agreement to avoid caliber misalignment during version changes.

The tooth profile code is the most easily skipped item in the worm gear reducer Selection, and the most likely to be bitten two years later: it determines the processing route, efficiency, heat dissipation area, and also determines whether the accessories can be replaced individually. By determining the tooth shape according to working conditions, selecting parameters according to standards, leaving a temperature rise margin according to the efficiency range, and then writing the code name into the technical agreement, the problems of temperature rise, wear and spare parts will basically be blocked. If you need to calculate the tooth profile plan according to working conditions or compare and replace imported models, you can contact Hangzhou Weigao Transmission. We manufacture hard tooth surface reducers, worm gear reducers, cycloidal pinwheel reducers and gear reduction motors, and can issue accounting opinions based on center distance and tooth profile code.

Latest News

WeiGao Transmission

Weigao Gear Reducer is an alliance group company that integrates research and development, production, sales, and service

+86 400 801 9158

Email: sales@wgt.net.cn;wgt.net.cn@gmail.com
Tel:+86571 85023000

WEIGAO REDUCER

FEEDBACK