Author: Site Editor Publish Time: 20-11-2026 Origin: Site
1. Misunderstandings in lubrication management
1. Only add new oil and do not clean the old oil
Many maintenance personnel directly add new oil when they find that the oil level is low, or simply drain it when changing the oil. After long-term operation of the gearbox, metal wear debris and sludge will be generated inside. If the cavity is not cleaned, the remaining impurities will continue to rub along with the gear mesh, accelerating the wear of precision transmission components.
2. Wrong and random mixing of oil products
Failure to strictly follow the equipment instructions to select industrial gear oil of specified grade and viscosity (such as N110-N200 medium extreme pressure gear oil). Different brands and models of lubricants have different additives. Mixing them will change the viscosity of the oil, destroy the stability of the oil film, and cause abnormal noise and vibration.
3. Inaccurate oil quantity control
It is a common mistake to think that "the more oil, the better". Overfilling will cause the internal pressure of the gearbox to rise, causing severe heating and oil leakage; insufficient oil will cause local dry friction, leading to dry grinding of gears and damage to bearings.
2. Misunderstandings about operation and working conditions
1. Ignore the running-in and observation in the early stage of operation
If a new reducer or equipment after overhaul is put into operation in the initial stage (about 300 hours), if it is directly operated at full load and at high speed, it will cause hidden damage to the internal parts. The correct approach is to appropriately reduce the load and closely observe the temperature rise and noise. The first oil change must be performed after this stage.
2. Blindly increase the power of the equipment or overload operation
Running the gearbox beyond the load limit specified on the nameplate for a long time, or frequently subjected to huge impact loads, will greatly shorten the life of the equipment, and even lead to serious failures such as overheating and burning of the motor coils and broken gear teeth.
3. Misunderstanding "maintenance-free" as "no maintenance"
Some modern gearboxes are designed to last a long time, but they are not maintenance-free. Failure to perform regular oil level checks, seal condition assessments, and connecting fastener rechecks after installation will still lead to premature equipment failure.
3. Misunderstandings in installation and assembly
1. Poor installation alignment and insufficient base rigidity
The installation between the reducer, motor and working machine is crucial to neutrality. Small misalignments will be amplified in long-term operation, resulting in additional bending moments and radial forces, causing severe vibration, noise and bearing damage.
2. Violent percussion assembly
When replacing gears or bearings, directly hitting the parts with a hammer will cause hidden damage to the parts. There may be no obvious failure in the short term, but the wear will be accelerated in the later period.
3. Neglect the maintenance of vent plugs and seals
If the vent plug is blocked, the pressure inside the box cannot be released normally, and the sealing structure will continue to be squeezed, causing the seals to age and fail, forming a vicious cycle of oil leakage. In addition, if the sealing ring is damaged and not replaced in time, the precision parts will become oxidized due to moisture.
4. Misunderstandings in troubleshooting
1. Continue to run forcefully after abnormal noise occurs.
When abnormal knocking sounds or sharp noises occur in the equipment, choosing to "persevere despite illness" due to tight production tasks will lead to the rapid expansion of the scope of the fault and turn small problems into major repairs.
2. Passively wait for a fault to occur
Lack of regular temperature, vibration and noise inspection system. Temperature is usually the first indicator of gearbox failure. If the temperature rises rapidly and becomes unstable, the machine must be shut down immediately for troubleshooting rather than waiting for the equipment to completely fail.
Avoiding these maintenance misunderstandings and establishing a scientific lubrication and condition monitoring system can not only effectively reduce the equipment failure rate, but also significantly extend the service life of the B series gearbox.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?