Author: Site Editor Publish Time: 14-11-2026 Origin: Site
On a dry bulk carrier the deck winch works hard for twenty minutes during berthing, then sits idle in salt fog for days. A marine gearbox picked from a standard industrial catalogue rating survives the torque yet fails within two years, because the controlling constraints differ afloat. Duty class, holding torque and C5-M corrosion protection set the frame size before the thermal table does. This article walks through a recalculable 120 kN mooring winch example end to end.
Three facts change the specification. First, the atmosphere: deck equipment lives in ISO 12944 C5-M corrosivity, where salt attacks unprotected machined faces within weeks. Second, the load: rope pulls arrive as shock when the line snaps taut, so the service factor gearbox rating must cover impact, not just steady torque. Third, the duty: winches run short, frequent cycles matching IEC 60034-1 S4 rather than S1, and the reducer should carry the equivalent FEM 9.511 / ISO 4301 class; enclosures reach IP56 minimum.
ISO 4301 groups deck machinery by load spectrum and cycle count. Mooring winches on deep-sea vessels typically fall in M5–M6, anchor windlasses near M5, frequent-duty crane slewing at M6–M7. Quote the gearbox against the same class, not an S1 number that ignores cycling.
Application | ISO 4301 / FEM class | IEC 60034-1 duty | Typical service factor |
|---|---|---|---|
Mooring winch drive | M5–M6 | S4, 25–40% CDF | 1.6 |
Anchor windlass | M5 | S4, 25% | 1.75 |
Deck crane hoist | M6 | S4, 40% | 1.75–2.0 |
Gangway / provision winch | M4 | S3, 15% | 1.4 |
Specification: rated line pull 120 kN at first layer, rope speed 0.5 m/s, Ø40 mm wire rope on a 600 mm bare drum, 4-pole motor at 1,450 rpm. The drum carries an open gear of 1.8 m pitch diameter driven by the gearbox output pinion.
Pitch diameter D = 0.600 + 0.040 = 0.640 m. Drum torque T = F × D/2 = 120,000 × 0.320 = 38,400 N·m. Drum speed n = 60v/(πD) = 60 × 0.5/(π × 0.640) = 14.92 rpm. Rope power P = F × v = 60 kW. Note the trap: upper layers grow the pitch diameter, so drum torque reaches 52,800 N·m at the fourth layer (D = 0.88 m) while speed falls — the motor stays at 60 kW, which is why line pull is always quoted at first layer.
Required ratio i = 1,450/14.92 = 97.2 → take a three-stage bevel-helical gearbox at i = 97 (output 14.95 rpm). At efficiency 0.95, shaft power = 60/0.95 = 63.2 kW → select a 75 kW motor (input torque 9,550 × 75/1,450 = 494 N·m, against a demand of 38,400/(97 × 0.95) = 416.5 N·m, a 19% margin). Apply the shock service factor of 1.6 from the duty table: 38,400 × 1.6 = 61,440 N·m → select rated output torque 63,000 N·m. A reducer rated at bare 38,400 N·m will pit its gear teeth within one berthing season.
Parameter | Value | Basis |
|---|---|---|
Line pull (1st layer) | 120 kN | vessel specification |
Pitch diameter, 1st layer | 0.640 m | 0.600 m drum + Ø40 rope |
Drum torque | 38,400 N·m | F × D/2 |
Drum speed | 14.92 rpm | 0.5 m/s rope speed |
Rope power / shaft power | 60 kW / 63.2 kW | η = 0.95 |
Motor | 75 kW, 1,450 rpm | 19% torque margin |
Gearbox | i = 97, 63,000 N·m | SF 1.6, class M5–M6 |
A mooring winch must hold the ship, not only move it. The rule: holding torque ≥ 1.5 × full-line drum torque = 1.5 × 38,400 = 57,600 N·m. Two placements exist. A low-speed drum band brake rated 60,000 N·m sits on the drum itself and holds with no back-drive loss — the standard solution for windlasses and mooring winches. A motor-mounted spring-applied brake sees only 1.5 × 38,400/(97 × 0.9) = 660 N·m of demand, but holds through the gear mesh, where backlash lets the drum creep. For holding torque that keeps a vessel stationary, the drum brake wins; the motor brake stays as a parking brake. Never rely on worm self-locking as the primary holding device on a winch — vibration and wear degrade it.
Paint against ISO 12944 C5-M: Sa 2.5 blast, zinc-rich epoxy primer + MIO epoxy + polyurethane topcoat, DFT ≥ 320 µm, machined shaft ends shrouded. Gearbox and motor enclosures at IP56 or better; output seals should be cassette-type because high-pressure deck washing is routine. Fit a desiccant breather, not an open vent, so daily thermal breathing does not draw salt-laden air into the oil; prefer FKM to NBR in tropical service. These details cost little at build yet dominate the failure record — most gearbox troubleshooting cases we see from vessels trace to salt water past a seal, not gear fatigue.
Check the output bearing carrying the open-gear tangential force: Ft = 38,400/0.9 = 42.7 kN. With a 20% mesh-shock allowance, P = 51.2 kN against a spherical roller bearing of C = 560 kN at 14.95 rpm: L10h = (560/51.2)^(10/3) × 10⁶/(60 × 14.95) ≈ 3.2 million hours, still over 800,000 hours with a 1.5× shock factor. Low-speed marine drives are rarely bearing-limited; the effort belongs in duty class, brakes and sealing.
Do not skip the thermal table entirely. In stand-alone heave the winch can run near S1: losses at 5% of 63.2 kW = 3.16 kW. A 3 m² housing dissipates 3 × 12 = 36 W/K, giving ΔT = 3,158/36 ≈ 88 K — a 123 °C sump at 35 °C ambient, unacceptable. With a fan or forced-oil loop rated ≥ 90 W/K, ΔT falls to 35 K and the sump settles near 70 °C. This is where an S4 rating can mislead: cycling cools the motor, but a long static hold consumes the gearbox thermal power margin all the same.
Check | Acceptance criterion |
|---|---|
Vibration, rated speed | ISO 20816-3 Zone A, ≤ 2.8 mm/s RMS |
Gear contact pattern | 40–60% face width, centred; backlash recorded |
Loaded run | 100% first-layer pull on test stand where possible |
Seals after 2 h hot run | Zero leakage; breather and cassette seals confirmed |
Coating / enclosure | C5-M DFT ≥ 320 µm records; IP56 test report |
Brake holding test | 1.5× rated drum torque, both directions |
The 120 kN winch above needed a 63,000 N·m, i = 97 bevel-helical marine gearbox with a 60,000 N·m drum brake and a C5-M paint system — a specification built from duty class and environment, not a single catalogue torque. To size your own deck winch, windlass or crane drive, try the WGT online gearbox selection system. We also supply SEW, NORD and Flender compatible replacement gearboxes for shipboard retrofits where the original footprint must be kept. Send the line pull, rope speed and duty profile for a full calculation sheet.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?