Author: Site Editor Publish Time: 11-11-2026 Origin: Site
In addition to the model and number of teeth, the reducer drawings are often marked with a series of numbers like x 1 = +0.30 and x 2 = −0.30, which are the displacement coefficients. It is not a decoration: if the number of teeth is less than a certain lower limit, undercutting will occur. If the number of teeth is enough but the center distance does not match the box body, it will not fit in either. The displacement coefficient is a means to solve these two problems at the same time.
When using a standard rack tool to process an involute gear, if the number of teeth is too small, the top line of the tool tooth will cross the meshing limit point and cut off the formed involute tooth root. This is called undercutting, and the tooth root strength will be weakened. The minimum number of teeth to avoid undercutting is z min = 2h a * /sin 2α, where h a * is the tooth addendum height coefficient and α is the pressure angle. Taking h a * = 1 and α = 20°, substitute z min = 2/sin 220° = 17.10. In engineering, 17 teeth are used as the boundary.
When the number of teeth is insufficient, positive displacement can be used to move the tool outward by xm (x is the displacement coefficient, m is the module) to thicken the tooth thickness and tooth root, thereby avoiding undercutting. The corresponding minimum displacement coefficient is x min = ha * ( z min − z)/z min , and a margin should be left for the actual value.
Number of teeth z | Minimum displacement coefficient x min | Number of teeth z | Minimum displacement coefficient x min |
|---|---|---|---|
12 | 0.2981 | 16 | 0.0642 |
13 | 0.2396 | 17 | 0.0057 |
14 | 0.1812 | 18 | −0.0528 |
15 | 0.1227 | 20 | −0.1698 |
The standard center distance of a pair of standard gears a = m(z 1 + z 2)/2 is directly calculated from the module and the number of teeth, and there is no room for adjustment. When the box hole spacing has been processed to a non-standard value, or if you want to reduce it Dimensions, you have to rely on displacement. According to the relationship between the total displacement coefficient and the center distance variation coefficient y = (a′ − a)/m, transmission is divided into three categories: height displacement (x 1 + x 2 = 0, a′ = a), positive angular displacement (x 1 + x 2 > 0, a′ > a) and negative angular displacement (x 1 + x 2 < 0, a′ < a).
There is an identity that is easily overlooked: as long as the calculation is carried out according to the formula, the head clearance will always remain c*·m regardless of height or angle displacement. In this example, m = 3 mm. The calculated head clearances of the three options are all 0.750 mm, which is exactly equal to 0.25m.
Take the high-speed stage of a two-stage reducer: module m = 3 mm, pressure angle 20°, h a * = 1, c * = 0.25, speed ratio i = 4. In order to compress the axial size, z 1 = 13 for the small gear and z 2 = 52 for the large gear. Standard center distance a = 3×(13 + 52)/2 = 97.50 mm.
z 1 = 13 is lower than the 17-tooth limit, and the standard gear must be undercut. According to x min = 0.2396 and leave a margin, take x 1 = +0.30, and match x 2 = −0.30, which is a high degree of displacement. At this time, a′ = a = 97.50 mm, y = 0, and the tooth addendum height variation coefficient σ = 0.
project | Teeth 1 standard gear x=0 | Tooth 1 after displacement x=+0.30 | Tooth 2 after displacement x=−0.30 |
|---|---|---|---|
Tooth tip circle diameter da (mm) | 45.000 | 46.800 | 160.200 |
Tooth root circle diameter df (mm) | 31.500 | 33.300 | 146.700 |
Tooth tip height ha (mm) | 3.000 | 3.900 | 2.100 |
Tooth root height hf (mm) | 3.750 | 2.850 | 4.650 |
Indexing scallop thickness s (mm) | 4.712 | 5.368 | 4.057 |
Tooth tip thickness sa (mm) | 1.903 | 1.382 | 2.450 |
Ratio of tooth tip thickness to module sa/m | 0.634 | 0.461 | 0.817 |
The diameter of the indexing circle d = mz, the diameter of the base circle, the module, and the pressure angle do not change with the displacement. What changes is the tip circle, the tooth root circle, the tooth thickness, and the tooth space width. After positive displacement of the pinion, the tooth root height is reduced from 3.750 mm to 2.850 mm, and the tooth root is thickened; after negative displacement of the large gear, the tooth addendum height is reduced from 3.900 mm to 2.100 mm, but the tooth addendum thickness increases to 2.450 mm. This is the distribution logic of height displacement: concentrate the displacement on the pinion with thin teeth and weak tooth roots.
Positive displacement thins the pinion tip. The tooth tip thickness is calculated according to s a = d a [π/(2z) + 2x·tanα/z + invα − invα a ], invθ = tanθ − θ (radians). Limits in Chapter 13 of 'Mechanical Design Manual': general gear s a ≥ 0.25m, quenched parts > 0.4m, this example is satisfied by 0.461. The transition curve interference is checked according to the two formulas in Table 13-1-5 of the manual, and the margins of 0.0279 and 0.0480 are both satisfied; the degree of coincidence ε α = 1.526, which is higher than the 1.2 limit.
For the same speed ratio i = 4 and the same module, if the number of teeth is different, the center distance will be different: 97.50 mm for the 13-tooth solution, 127.50 mm for the 17-tooth standard solution, and 150.00 mm for the 20-tooth solution. The center distance of the 13-tooth displacement scheme is 30.00 mm less than that of the 17-tooth scheme, a decrease of 23.53%. This is the actual value of the displacement transmission with a small number of teeth: making the box smaller and flatter under the same load-bearing requirements, the premise is that the three tests of tooth tip thickness, interference, and coincidence are all passed.
x 1 value | Tooth 1 Tooth tip thickness sa/m | Tooth 2 Tooth tip thickness sa/m | Degree of coincidence ε α | Tooth 1 root circle df (mm) | Interference condition 1 margin |
|---|---|---|---|---|---|
+0.20 | 0.5236 | 0.8055 | 1.554 | 32.70 | 0.0356 |
+0.25 | 0.4928 | 0.8113 | 1.540 | 33.00 | 0.0316 |
+0.30 | 0.4606 | 0.8167 | 1.526 | 33.30 | 0.0279 |
+0.35 | 0.4272 | 0.8217 | 1.511 | 33.60 | 0.0244 |
+0.40 | 0.3925 | 0.8262 | 1.495 | 33.90 | 0.0210 |
This table shows that the larger the displacement coefficient, the better. As x 1 increases, the tooth root circle increases and the tooth root strength increases, but the tooth tip thickness decreases all the way, and the coincidence degree and interference margin are tightened simultaneously. When x 1 = +0.40, s a /m drops to 0.3925, which is lower than the upper limit of 0.4m required for quenched gears. At this time, the displacement must be reduced, tooth tip trimming must be used instead, or the number of teeth must be retreated. The value range should be inferred from the most stringent limit.
The box hole spacing requires a center distance a′ = 100 mm, which is 2.50 mm different from the standard center distance of 97.50 mm. This is a positive angular displacement. From cosα′ = (a/a′)cosα, we get cosα′ = (97.50/100)×cos20° = 0.9162, meshing angle α′ = 23.62°, and then use invα′ = invα + 2tanα(x 1 + x 2)/(z 1 + z 2) to solve for the total displacement coefficient x 1 + x 2 = 0.9076, and the center distance variation coefficient y = (100 − 97.50)/3 = 0.8333, tooth top height variation coefficient σ = x 1 + x 2 − y = 0.0743. Take x 1 = +0.50, x 2 = +0.4076.
project | numerical value | project | numerical value |
|---|---|---|---|
Actual center distance a′ (mm) | 100.000 | Engagement angle α′ (°) | 23.62 |
Total displacement coefficient x 1 + x2 | 0.9076 | Center distance variation coefficient y | 0.8333 |
Tooth tip height variation coefficient σ | 0.0743 | Head clearance c (mm) | 0.750 |
Tooth 1 Addendum circle da (mm) | 47.554 | Tooth 2 Addendum circle da (mm) | 164.000 |
Tooth 1 root circle df (mm) | 34.500 | Tooth 2 root circle df (mm) | 150.946 |
Tooth 1 indexing circular tooth thickness s (mm) | 5.804 | Tooth 2 indexing circular tooth thickness s (mm) | 5.603 |
Tooth 1 Tooth tip thickness sa/m | 0.4401 | Tooth 2 Tooth tip thickness sa/m | 0.7733 |
End surface coincidence degree ε α | 1.338 | Interference conditions 1, 2 margin | 0.0558, 0.0469 |
The positive angle displacement simultaneously thickens the tooth thickness of the two gears and widens the center distance. The tooth root strength and contact strength are improved, but the coincidence degree is reduced to 1.338, which is smaller than the 1.526 of the height displacement scheme. The rule is: the farther the center distance is, the larger the meshing angle will be, and the greater the loss of coincidence will be. If the center distance deviation of the box is very small, it is often safer to use height displacement instead.
Whether the displacement coefficient is processed according to the drawing, it is most direct to measure the normal length W k . Formula W k = m·cosα·[(k − 0.5)π + z·invα] + 2x·m·sinα, k = αmz/1800 + 0.5 takes an integer. The latter term 2x·m·sinα is the displacement increment: when m = 3 mm, every 0.10 displacement coefficient corresponds to 0.205 mm, m = 4 mm corresponds to 0.274 mm, and m = 6 mm corresponds to 0.410 mm. Taking z = 13 and m = 3 as an example, the nominal W k = 4.974 mm for x = 0 and the nominal value of x = +0.30 is 5.590 mm; if the actual measurement is 5.590 mm, the back calculation x = (5.590 − 4.974)/(2×3×sin20°) = 0.300 is consistent with the drawing.
First determine whether the number of teeth exceeds the limit. Judge according to z min = 2h a * /sin 2α. The lower limit of straight teeth is 17 teeth when α = 20°; the helical teeth are converted according to the equivalent number of teeth z v = z/cos 3β. When β = 15°, z = 13 gives z v = 14.42. The minimum normal displacement coefficient is reduced to 0.156, which is looser than the 0.2396 of straight teeth.
Then determine the transmission type. If the center distance is consistent with the standard value, use height displacement. If the center distance needs to be widened, use positive angle displacement.
Assign the deformation coefficient. The small gear assumes positive displacement and the large gear assumes negative displacement, and starts with a margin of x min .
Make three checks. Tooth tip thickness s a ≥ 0.25m (quenched parts > 0.4m), transition curve interference type, coincidence degree ε α ≥ 1.2, if any of them fails, adjust x or change the number of teeth.
Calculate geometric dimensions and review loads. Draw the diagram according to da, df, s, s a , and then check the contact and bending strength according to GB/T 3480.2-2021 and GB/T 3480.3-2021; the simplified algorithm can be based on GB/T 10063-1988, which is applicable when the basic tooth profile complies with GB/T 1356, the rotation speed n ≤ 3600 r/min, and the indexing circle peripheral speed 1 m/s < v < In the case of 35 m/s, the two-stage peripheral speed in this example is 2.96 m/s.
Arrival review. Use the length of the common normal to infer the actual x and check it with the drawing.
Boundary tip: The displacement coefficient is only applicable to involute cylindrical gear transmission. Worm gear reducers are implemented in accordance with GB/T 10085-2018 and GB/T 10088-2018, and cycloidal pinwheel reducers are implemented in accordance with GB/T 10107 series and GB/T 36491-2018. Neither of them can apply the formula in this article. If the drawing of the hard-tooth surface reducer is marked with both the displacement coefficient and the accuracy grade, the accuracy shall be in accordance with GB/T 10095.1-2022, and the two items must be checked separately.
The displacement coefficient is just a few numbers on the drawing, but the trade-off behind it is the balance of a set of constraints: the undercut gives the lower limit of the number of teeth, the center distance deviation determines the transmission type, and the three checks of tooth tip thickness, coincidence degree, and interference delineate the upper limit of the displacement. If you need to calculate the displacement plan according to specific working conditions, or compare and replace imported models, you can contact Hangzhou Weigao Transmission. We make hard tooth surface reducers, worm gear reducers, cycloidal pinwheel reducers and gear reduction motors, and can issue accounting opinions based on the number of teeth, center distance, accuracy level and temperature rise.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?