Author: Site Editor Publish Time: 26-10-2026 Origin: Site
1. Preliminary judgment without disassembly (quick core inspection)
Running sound identification: Use the listening stick against different parts of the box. If there is a periodic metal knocking sound, continuous sharp friction sound, or the noise continues to exceed 85 decibels, it indicates the risk of wear of the meshing surface, pitting corrosion or broken teeth.
Vibration abnormality troubleshooting: Use a portable vibration detector to collect the spectrum. A sudden increase in high-frequency components corresponds to abnormal worm gear meshing, and an intensification of low-frequency vibration is associated with meshing dislocation caused by shaft system positioning deviation.
Temperature abnormality location: The temperature rise of the bearing part exceeds 70℃, and the oil pool temperature continues to be higher than 90℃. It is most likely that the transmission pair is overheated due to intensified friction on the meshing surface and failure of lubrication.
Feel cranking test: Manually crank the input shaft after the power is turned off. If the rotation resistance suddenly increases and sometimes decreases, there is an obvious stuck feeling, or a large amount of free travel occurs when switching forward and reverse, it means that the meshing clearance has seriously exceeded the standard.
2. Quantitative indicator verification (hard indicator determination)
Speed deviation verification: Use a tachometer to measure the input and output speeds respectively, and calculate the actual reduction ratio. If the deviation from the design value exceeds ±3%, it can be determined that the transmission pair has wear slippage or meshing stuck.
Return clearance measurement: Lock the input end and use a dial indicator to measure the idle clearance in the circumferential direction of the output shaft. If the value far exceeds the factory standard of the new machine, it means that the worm gear tooth thickness has been seriously reduced and the meshing surface wear has exceeded the limit.
Oil condition analysis: Take a sample from the oil drain hole and observe that the oil is black and turbid, and shiny copper/iron metal particles appear on the white paper, which is direct evidence that the tooth surface of the worm gear is peeled off and glued.
3. Disassembly and inspection (final confirmation)
Worm component inspection: Visually inspect the tooth surface for pitting pits and glue adhesion marks, and use a dial indicator to measure the radial runout of the worm journal. If the deviation exceeds 0.03mm, it indicates that the worm is bent and deformed, which will directly lead to meshing misalignment.
Worm gear component inspection: Focus on checking the uniform wear and eccentric wear of the copper worm gear tooth surface. If the overall tooth thickness is reduced by more than 10% of the original thickness, or the local tooth top is chipped, the transmission pair has completely failed.
Meshing clearance verification: Use a feeler gauge to measure at 4 uniform points on the worm gear meshing surface. The standard meshing clearance of the WP series is 0.1-0.3mm. A clearance >0.5mm indicates severe wear. A clearance <0.1mm indicates excessive assembly or tooth surface gluing.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?