Author: Site Editor Publish Time: 02-11-2026 Origin: Site
1. External installation and connection inspection
Retighten all anchor bolts and tighten diagonally step by step according to the specified torque of 80~120N·m. Check that the base gasket is not misplaced and the foundation is not cracked or loose.
Use a dial indicator to calibrate the coaxiality of the shaft system, control the radial deviation ≤ 0.05mm, angular deviation ≤ 0.05mm/m, and correct the alignment error of the motor-reducer-load.
Check the buffer parts of the elastic coupling to confirm that the plum blossom pad/rubber sleeve has no aging and cracking. The matching gap between the flat key and the keyway is ≤0.1mm to eliminate transmission impact.
2. Low load adaptation adjustment of lubrication system
Adjust the oil level to the 1/2~2/3 range of the oil mirror to avoid excessive oil stirring resistance caused by excessive oil level under low load, or insufficient oil level causing insufficient lubrication of the meshing surface.
Take a sample to check the oil quality. If the oil turns black and contains metal debris, replace it immediately. Use L-CKE 220# extreme pressure worm gear oil to ensure a stable oil film on the sliding friction surface.
Clean the clogged respirator to prevent the temperature difference between the inside and outside of the box from forming a negative pressure to absorb moisture, and to prevent water vapor from intruding and destroying the lubrication state.
3. Core transmission deputy status verification
Retest the worm gear meshing backlash and control the standard value stably within the range of 0.15~0.3mm. Under low load, too large a backlash can easily cause reverse impact, while too small a backlash can cause sticking and heating.
Check the bearing clearance. The axial clearance is controlled at 0.03~0.05mm. If pitting corrosion occurs on the raceway or the rolling elements peel off, immediately replace the matching bearing of the same model.
Monitor the abnormal noise in the meshing part. If there is sharp periodic friction sound, disassemble and check the tooth surface wear. If the tooth thickness is thinned by more than 5%, replace the worm gear pair in pairs.
4. Calibration of low load operating parameters
Adjust the torque limit in the frequency converter to 1.2~1.5 times the actual load to avoid output torque fluctuations caused by "big horse-drawn carts" and transmission shock.
The stable input speed is in the range of 300~1500rpm. It is strictly prohibited to operate at extremely low speed for a long time to prevent the sliding friction surface from forming a dynamic pressure oil film and causing dry wear.
Use a vibration meter to monitor the vibration speed to ensure that the vibration value of the whole machine is ≤7.1mm/s. If the low-frequency vibration peak is too high, the base stiffness can be appropriately increased to avoid low-load resonance.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?