Author: Site Editor Publish Time: 26-10-2026 Origin: Site
SelectionAfter calculating the torque, speed ratio and thermal power, we only determined 'which gear to use'. Whether it can land on the ground depends on the installation size of the reducer . Failures in on-site installation are usually divided into three categories: the geometric interface is misaligned, the distance between the foot holes, the center height, and the shaft extension do not match the original equipment; the tolerance fit is not read thoroughly, the shaft extension mark k6 is processed according to h6, and the coupling H7 hole is loose when installed; there is not enough space left, the oil drain plug is attached to the foundation, and the vent cap top shield is attached. The first two types can be stopped with a drawing and a caliper before ordering. When they arrive at the site, they find that they can only expand the hole, add a backing plate or even change the model.
Interface part | drawing elements | Frequently Asked Questions | as a result of |
|---|---|---|---|
Footing hole spacing and hole diameter | A1×B1, n-φd | Hole distance deviation ≤±0.5 mm, bolt verticality ≤0.5° | The holes don"t match up, so we can only expand the holes. |
Center high | h | Mark the value according to the GA diagram and check the diagonal by actual measurement. | The pad iron is hard to form a soft foot , and the bearing is eccentrically loaded. |
Output shaft extension | d×l, key b×h | For d≤50 mm, take k6, for d>50 mm, take m6, and the key width is h8. | Failed to install or crashes after running |
input flange | Stop, screw hole PCD | Stop b1≤230 mm uses j6, >230 mm use h6 | The motor is installed incorrectly and the vibration exceeds the standard. |
Hollow shaft hole | d. Keyway width | Bore diameter H7, groove width shaft N9, hub JS9 | The shaft sleeve does not advance or slips |
Attachment orientation | Oil plug, oil mark, breather cap | Changes with installation orientation M1~M6 | Oil change requires lifting equipment |
What is easy to overlook in dimensioning is the 'tolerance zone is bound to the diameter': both are k6, the 45 mm axis is +0.018/+0.002 mm, and the 70 mm axis is +0.030/+0.011 mm according to m6. If you copy the markings, you will make out-of-tolerance parts. The general method is to use k6 for solid shaft ≤50 mm, m6 for >50 mm, and the hollow shaft hole H7 to match the customer shaft h6. Taking 60 mm as an example, the gap falls between 0.019~0.049 mm, which can be pushed forward without shaking. The keyway is taken according to GB/T 1096: a 70 mm shaft is equipped with a 20×12 flat key, the groove depth is 7.5 mm, the key width is h8, the shaft groove width is N9 (0~-0.052 mm), the hub groove width is JS9 (±0.026 mm), and the symmetry is controlled within 0.03 mm. Otherwise, the key will be deflected in the groove and the torque will only be borne by one edge.
The flange seam determines the coaxiality of the motor and the reducer. If the seam or PCD is out of tolerance, it will look good when installed. The measured runout is above 0.1 mm, and the bearings and oil seals will fail prematurely. The hole diameter, keyway and locking method of the hollow shaft must be checked at the same time, and axial space must be reserved for the disassembly and assembly of the shrink disk structure.
Check items | What to look for on the drawing | Judgment points |
|---|---|---|
Installation orientation | M1~M6 code and oil level line | Consistent with the on-site attitude, the oil level can be observed |
footing | A1×B1, hole diameter, bolt specifications | Correspond to the reserved holes in the foundation, leaving 2~3 mm |
Center high | h and shaft extension centerline | Consistent with the original equipment elevation |
Shaft extension | d×l, key b×h, center hole | Center hole GB/T 145 C type, key length covers the hub |
flange | Stop, PCD, screw hole depth | Comparison with actual measurement of motor flange |
appendix | Oil plug, oil mark, breather cap, lifting lugs | Leave operating space around |
Weight and center of gravity | Net weight, center of gravity elevation | The basic load capacity is not less than 3 times the weight of the entire machine |
After the drawings have been verified, they must be remeasured on site. First, clean the base surface to remove burrs and oil stains, use a knife-edge ruler and a feeler ruler to check the flatness , control it within 0.1 mm/m, and the bonding area should not be less than 75%. Second, measure the hole spacing twice along the diagonal and take the average, and the deviation is controlled within ±0.5 mm. Third, measure the center height of the height ruler and benchmark it with the original equipment. If the difference is more than 3 mm, do not rely on the pad iron to align it. Instead, add equal thickness pads to the entire surface. Fourth, use a micrometer to measure the shaft extension size and roundness, and a caliper to measure the key width and groove width. Fifth, manually turn the car for one or two turns to confirm that there is no jamming, and then check whether the oil plug and oil mark are within reach.
The center height difference is 3 mm, and the inclined pad iron is used as a hard pad. When the anchor bolts are tightened, the box will be stretched and deformed by 0.1~0.2 mm. The raceway will be eccentrically loaded and the oil seal will be eccentrically worn. The key length is 10 mm shorter than the effective length of the hub, and the pressure is insufficient. The key is sheared and the shaft extension is sprained under impact conditions. The oil drain plug faces the foundation, and the equipment must be lifted every time the oil is changed. The gap between the motor flange and the gap is 2 mm, which needs to be flattened by bolts, and the coaxiality is damaged. Tighten according to the 8.8 grade bolt torque: 45~55 N·m for M12 and 120~140 N·m for M16. Tighten diagonally to the rated value in two or three times, and retighten once every 24 hours.
Sign and confirm the GA drawing as an attachment to the contract. The model, speed ratio, installation orientation, shaft extension and key, flange stopper, oil plug orientation and weight are indicated on the drawing. Changes must be confirmed in writing. Before shipment, review the drawing according to the drawing and keep records. Upon arrival, unpack and randomly inspect the shaft extension diameter, key width and anchor hole spacing. Any deviations shall be reported during the acceptance period.
The order is worth remembering: first check the footing and center height , then check the shaft extension and keyway , and finally check the accessories and maintenance space - the first two determine whether it can be installed, and the latter determines whether it can be maintained in the future. Hangzhou Weigao Transmission can provide GA drawings and dimensional tables of hard-toothed surface reducers , 、cycloidal pinwheel reducers , worm gears and gear reduction motors, etc., and supports customizing shaft extensions, flanges and foot arrangements according to customer interfaces. When replacing an in-service model, send the original machine nameplate and actual measured dimensions, and the reducer manufacturer can provide Selection and size verification services free of charge.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?