Author: Site Editor Publish Time: 30-10-2026 Origin: Site
1. Appearance inspection of fully sealed points
Shaft extension end seal: Focus on checking the skeleton oil seals of the input shaft and output shaft, check whether there is oil slinging and accumulation of oil stains on the shaft head, and whether there are signs of aging, cracking, deformation, or wear on the edges of the oil seals.
Box joint surface: Check the sealing status of the upper and lower box middle planes and bearing end covers to confirm that there are no traces of oil leakage and that there are no sealing gaps caused by loosening of the connecting bolts.
Auxiliary sealing parts: Check the oil level gauge, oil drain plug, inspection hole cover, and O-ring/gasket at the flange connection position to confirm that there are no signs of hardening, water or oil leakage.
Surface cleaning: Clean the dust and debris accumulated around the seal in time to prevent hard particles from entering the sealing gap and accelerating the wear of the oil seal lip.
2. Verification of key sealing accuracy
When the machine is stopped, use a 0.05mm feeler gauge to check the fit gap between the connection surface of the box cover and the box body. If the feeler gauge cannot be inserted, the sealing fit is qualified.
Check the oil seal installation coaxiality and confirm that there are no obvious axial scratches on the journal surface to avoid seal failure caused by eccentric wear of the lip.
Mark and track minor oil leakage points. If the oil leakage area exceeds 5cm² within 24 hours, it needs to be dealt with in advance to avoid developing into an oil leakage failure.
3. Oil status correlation verification
Stop the machine for 10-15 minutes and wait for the oil to flow back to check the oil level. If the oil level drops abnormally for no reason, it most likely corresponds to a seal leakage point.
Take a sample to observe the oil state: if there are signs of emulsification, whitening, or water intrusion, it means that the static seal has failed and water vapor has invaded the inside of the box.
When a large amount of metal debris is found in the filtered oil, the dust-proof ability of the seal should be checked simultaneously to confirm whether external impurities have entered the interior through the failed seal.
4. Review of running status
Monitor the local temperature around the seal during operation. If the temperature at the oil seal position exceeds 80°C, it means that the lip friction is overheated and the seal is close to aging and failure.
The leakage trend of the sealing points was recorded. New oil stains appeared during three consecutive inspections at the same location. It was necessary to arrange a shutdown to replace the seals to avoid sudden leakage and bearing failure caused by lack of oil.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?