Author: Site Editor Publish Time: 28-10-2026 Origin: Site
1. Basic preparation before listening
1. Prepare a long-handled listening needle or screwdriver, place the blade against different positions of the cabinet, and listen to the sound to avoid environmental noise interference.
2. First, disengage the coupling and run the motor independently without load to eliminate the interference of the abnormal noise of the motor itself; then load the motor according to the steps of 25%, 50%, 75%, and 100%, and record the sound changes under different loads.
3. Confirm in advance that the anchor bolts are not loose and the coupling is properly aligned to eliminate false abnormal noise caused by external factors.
2. Sound classification determination of different degrees of fracture
1. Early micro-crack stage (no obvious broken teeth)
Sound characteristics of the early micro-crack stage: there is almost no abnormal sound when no-load. Only when running at full load, a very subtle "rustling" friction sound accompanied by load fluctuations is emitted from the gear meshing area of the box. There is no obvious impact feeling, and the sound frequency is completely synchronized with the gear meshing frequency.
Auxiliary verification at the early microcrack stage: at this time, the vibration speed is usually ≤4.5mm/s, the oil temperature has no obvious abnormality, and only very fine metal powder can be found in the oil, indicating that the tooth root microcracks are in the early stages of expansion and have not yet formed a broken tooth gap.
2. Partially mildly broken teeth (the edge of a single tooth is chipped, the fracture area is <1/3 of the tooth width)
Sound characteristics of partial mild broken teeth: clear, periodic crisp "click" and "thump" impact sounds can be heard without load. The sound rhythm is strictly synchronized with the rotation speed of the low-speed output shaft. There is one obvious impact per revolution. When the load increases, the loudness of the impact sound will increase simultaneously.
Auxiliary verification of partial mild broken teeth: the vibration speed increased to 4.5~11.2mm/s, the local box temperature increased slightly, and a small amount of small flake metal abrasive grains could be found in the oil. At this time, only the local edge of a single tooth was broken, and the tooth root was not injured, which is a mild fracture damage.
3. Moderate complete single tooth fracture (whole tooth falls off)
The sound characteristics of a moderate complete single tooth fracture: the impact sound changes to a heavier "clunk" or "clang" sound, with a strong sense of impact. Even in the no-load state, you can directly hear obvious periodic metal impacts while standing next to the equipment. The higher the speed, the faster the frequency and louder the impacts.
Auxiliary verification of moderate complete single tooth fracture: the vibration speed exceeds 11.2mm/s, the gearbox oil temperature rises rapidly to above 70°C, and massive metal debris with a size of >0.5mm can be found in the oil. At this time, a single gear tooth has completely fallen off, and the broken tooth gap will produce a strong impact every time it meshes. This is a moderate fracture damage, and the machine must be stopped immediately to arrange for replacement.
4. Severe multi-tooth continuous fracture
Sound characteristics: The sound completely turned into a chaotic and chaotic sound of violent metal collision and friction. The original fixed periodic rhythm completely disappeared, and irregular "crash" noises appeared. There were even sharp metal dry friction whistling, and the entire equipment experienced strong shaking.
Auxiliary verification: The vibration speed far exceeds 11.2mm/s, the oil temperature soars to above 80°C in a short period of time, and a large number of large broken tooth fragments can be found at the bottom of the oil. At this time, two or more gear teeth have been broken continuously, and vicious accidents such as transmission jamming and shaft system deformation may occur at any time, and the power must be shut down in an emergency.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?