Author: Site Editor Publish Time: 26-10-2026 Origin: Site
Oil leakage may seem just 'dirty', but the actual consequences are very real: after the oil level drops, the gears and bearings enter a state of insufficient lubrication , and tooth surface gluing and bearing ablation often occur. The order of troubleshooting the cause of oil leakage in the reducer is: first look at the two 'zero cost' items of the breather cap and oil level, then check the transfer seal (shaft end oil seal) and static seal (joining surface, end cover) one by one, and then consider unpacking. On-site statistics show that about 60% of the oil leakage points are concentrated in the output shaft oil seal area, 30% are in the box joint surface, and the rest are in the oil drain plug and breather cap.
When the reducer is running, the oil temperature rises, and the air in the box expands to form a positive pressure. If the vent cap is blocked by dust or sludge, the internal pressure will squeeze the oil out from weak points such as the oil seal lip and the joint surface. The judgment method is very simple: when oil leaks from many places at the same time and the box temperature is high, it is likely that the ventilation is not smooth. During treatment, unscrew the ventilation cap to clear the small holes. If the blockage is serious, replace it directly. For working conditions with heavy dust, it is recommended to use an oil cup-type ventilation cap, increase the hole diameter to about 6 mm and purge it regularly. The worm gear reducer generates more heat than the cylindrical gear model, so the vent cap needs to be inspected more frequently.
When the oil level exceeds the upper limit of the oil level, the oil pool is violently stirred during operation, and the lubricating oil splashes and accumulates at the shaft seal and joint surface, leaking outward under the action of the pressure difference. Check the oil mark mark after stopping the machine for 10 to 30 minutes. The oil level should be between the upper and lower limits. If it is too much, drain it. The oil product is also critical: if the viscosity is low, the oil will be thin, if the viscosity is high, the oil will be stirred and heat will be generated, and if the viscosity of oil with poor anti-foaming properties is misused, the foam will raise the liquid level. Just add according to the sample grade.
There are three main modes of output shaft oil seal failure: First, the lip ages , the rubber hardens under high temperature and oil immersion, and oil leaks after the interference disappears; second, the journal is strained , and the surface grooves continue to scratch the lip; third, bearing wear increases the output shaft runout, and the eccentric wear of the oil seal accelerates. When replacing, follow the specifications for replacing the oil seal of the reducer : choose a double-lip oil seal with a spring skeleton, with the spring side facing the inside of the box, and use a guide set to insert it to avoid lip flanging. The shaft end is chamfered and oiled to prevent scratches. If the shaft neck has shallow grooves, it can be ground and repaired or the oil seal can be installed in a staggered position. If the output shaft is shaken and there is obvious slack, the bearing should be replaced first and then the oil seal, otherwise the new oil seal will wear out quickly.
Leakage at the joint surface of the upper and lower boxes and end covers is mostly caused by aging shrinkage and cracking of the sealant layer, uneven bolt pre-tightening, or poor flatness of the box. During maintenance, thoroughly remove old glue and burrs, re-apply oil-resistant sealant evenly, with a thickness of 0.2~0.5 mm to prevent glue from flowing into the tank and contaminating the oil, and then tighten the bolts evenly The flatness is checked with a knife-edge ruler and a feeler gauge. If the flatness is out of tolerance, it needs to be ground and repaired. When there is slight oil leakage at the static sealing point, polymer repair materials can be used as an emergency without stopping the machine. The adhesive layer should still be reprocessed during overhaul.in diagonal steps .
Oil leakage part | Typical phenomenon | main reason | Treatment measures |
|---|---|---|---|
vent cap | Oil leaks from multiple places at the same time and the oil temperature is too high | The ventilation holes are blocked and there is positive pressure in the box. | Unblock or replace the oil cup vent cap |
Shaft end oil seal | Oil drips along the shaft and worsens after shutdown | Lip aging, journal strain, bearing looseness | Replace the double lip oil seal, repair the journal, and check the bearing first |
joint surface | Oil leakage is flake-like and does not drip | Aging of the glue layer and uneven bolt pre-tightening | Clear the old glue, re-coat it, and fasten diagonally in stages. |
Oil drain plug/oil sight glass | Oil beads hanging on threads | The gasket is damaged or missing | Replace the oil-resistant gasket and tighten it to the specified torque |
Box cracks | Oil leakage points are fixed and gradually expanded | Casting defects or external collisions | After coloring and flaw detection, repair welding or replace the box. |
If the oil thrown by the gear to the bearing and end cover cannot flow back smoothly, it will accumulate and leak at the shaft seal. The idea of transformation is to open an oil return groove inclined toward the inside of the box in the center of the lower tile of the bearing seat. A gap is opened at the straight opening of the end cover to face the oil return groove; the high-speed shaft can be equipped with an oil slinger ring to retain oil. For reducers with a half-shaft structure, a spare oil seal can be pre-installed on the outside of the end cover . When it fails, it can be directly pushed in and replaced, eliminating the need to disassemble and remove the coupling.
Put the maintenance of the reducer in the front, so that oil leakage can be avoided: clean the breather cap once a month, check the appearance of the oil seal and the temperature of the shaft seal every quarter - if the infrared temperature measurement is 20 ℃ higher than that of the box, it indicates abnormal lip friction, and replacement should be arranged; combine oil samples every six months to track the wear trend. The cycle should be appropriately shortened under dusty and high-temperature working conditions, and oil seals and gaskets should be included in the standing list of wearing parts.
The core of oil leakage control is to identify the parts according to parts: vent cap first, then oil level, then seal, to avoid blind unpacking. Hangzhou Weigao Transmission provides a series of products such as hard-tooth surface reducers , worm gears, cycloidal pinwheels, and supporting oil seals, breather caps and other wearing parts. If you need on-site diagnosis of oil leakage, seal selection or new machine consultation, please contact our technical staff. The reducer manufacturer provides free maintenance and maintenance support.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?