Author: Site Editor Publish Time: 06-11-2026 Origin: Site
The reducer samples are marked with rated torque, but the output bearing rarely gives life data. Many people place orders after selecting the model based on torque. The result is that the gears have not pitted, but the bearings have broken first - the gear load-bearing capacity is based on the GB/T 3480 series, but the bearings are often 'guessed by torque'. GB/T 6391-2010 'Rolling Bearing Rated Dynamic Load and Rated Life' (equivalent to ISO 281:2007) provides a complete formula. This article uses it to calculate the load to life of a reducer output bearing, and provides troubleshooting steps that can be directly applied.
Bearing life check only requires five numbers, three from samples and two from operating conditions calculations. If you fill in these five numbers correctly, the lifespan conclusion will be certain, and there is no need to rely on experience.
parameter | symbol | Meaning and units | Value source |
|---|---|---|---|
Basic dynamic load rating | C | Bearing sample ratings in N (or kN) | Bearing sample, GB/T 6391-2010 definition |
Equivalent dynamic load | P | Equivalent load after conversion of radial and axial loads, unit N | Calculated, P = X·Fr + Y·Fa |
Equivalent static load | P0 | Converted load under stationary or extremely low speed conditions, unit N | Calculated, P0 = 0.6Fr + 0.5Fa |
Working speed | n | The rotation speed of the shaft where the bearing is located, unit r/min | Calculated from speed ratio |
life index | p | Take 3 for ball bearings and 10/3 for roller bearings | GB/T 6391-2010 |
Basic rated life in millions of revolutions: L10 = (C/P) p ; converted into hours: L10h = 10 6 / (60·n) × (C/P) p . This third power (roller bearing is 3.33 power) means that if the load estimation is slightly off, the service life will be significantly different. The following is the load sensitivity of the 6308 bearing (C = 40.8 kN, n = 58 r/min) in this calculation example.
Equivalent dynamic load P | L10h (hour) | Equivalent to baseline value | Interpretation |
|---|---|---|---|
×0.8 | 37 075 | 195% | The load is underestimated by 20% and the service life is nearly doubled. |
×1.0 | 18 982 | 100% | The base value of this calculation example |
×1.1 | 14 262 | 75% | The load is overestimated by 10%, and the service life is reduced by a quarter. |
×1.2 | 10 985 | 58% | The load is overestimated by 20%, and the service life drops to 60% |
×1.4 | 6 918 | 36% | The load is overestimated by 40% and the service life is less than 40% |
If replaced by a roller bearing (p = 10/3), the life span will only be 72.8% when the load is ×1.1, and only 54.5% when the load is ×1.2, which is more sensitive than a ball bearing. This is also one of the reasons why roller bearings are used more in 、hard-tooth surface reducers of cycloidal pinwheel reducers: it exchanges exponential margin for impact resistance.
The calculation example takes a two-stage spur gear reducer , the final output stage is extended to install a pulley drive, and all parameters are listed to facilitate item-by-item replacement.
project | symbol | value | illustrate |
|---|---|---|---|
Motor power | P1 | 11kW | Study settings |
Motor speed | n1 | 1 450 r/min | 4 pole asynchronous motor |
Overall speed ratio | i | 25 (5 × 5 two levels) | Typical configuration of two-stage hard tooth surface reducer |
total efficiency | η | 0.96 | The measured range of two-stage cylindrical gears is 0.95~0.97 |
Output speed | n2 | 58 r/min | n1/i=1450/25 |
Output torque | T2 | 1 738.8 N·m | T2 = 9550·P1·i·η/n1 |
final gear | m/z2/d2 | 6 mm / 75 teeth / 450 mm | Straight teeth, tooth width 60 mm |
gear circular force | Ft | 7 728N | Ft = 2·T2/d2 |
Support span | L | 250mm | Center distance between two bearings |
Wheeled cantilever | e | 100mm | Distal bearing extension |
Belt speed/initial tension | v/F0 | 4.0m/s/2000N | F0 = 500·v (v ≤ 4 m/s) |
load factor | fd | 1.3 | Gear transmission 1.2~1.5, take the middle value |
The radial force of the belt is calculated as Fr = 2·F0·sin(α/2). When the wrapping angle α = 180°, Fr = 2 × 2 000 = 4 000 N. The circumferential force of the belt Ft_belt = 1 000·P2/v = 1 000 × 10.56 / 4.0 = 2 640 N. Take the moment for proximal bearing A:
R_B × 250 = 7 728 × 70 + 4 000 × 350 = 1 940 960, R_B = 7 764 N ; R_A = 7 728 + 4 000 − 7 764 = 3 964 N. The distal bearing R_B is the control support, and the cantilever load raises its load to about twice that of the proximal bearing.
Spur gears have no axial component, Fa = 0, Fa/Fr ≤ e, take X = 1, Y = 0, so P = fd·Fr = 1.3 × 7 764 = 10 093 N. Equivalent static load P0 = 0.6 × 7 764 = 4 658 N.
plan | C/C0(kN) | L10h (hour) | Static strength safety factor s0 = C0/P0 | in conclusion |
|---|---|---|---|---|
6308(d=40mm) | 40.8/24.0 | 18 982 | 5.15 | The static strength is sufficient, but the service life is less than 25 000 h. |
6310(d=50mm) | 61.8/38.0 | 65 968 | 8.16 | Both lifespan and static strength are satisfied |
6312(d=60mm) | 81.9/52.2 | 153 540 | 11.21 | There is more margin, which can be used to extend the bearing replacement cycle. |
Use another algorithm for cross-validation: back-calculate the required dynamic load from the target life, C_req = P × (L10h·60·n / 10 6) 1/3 = 10 093 × (25 000 × 60 × 58 / 10 6) 1/3 = 44 722 N ≈ 44.7 kN . The 40.8 kN of 6308 is lower than this value, and the 61.8 kN of 6310 is higher than this value. The conclusions of the two algorithms are consistent. This shows that if the original Selection uses 6308, then when it reaches the end of its life on the gear reduction motor production line, it will still have the same failure point if it is replaced with the same type of bearing.
The same is 6308, only the cantilever length is changed: L10h = 24 572 h at 60 mm, 21 537 h at 80 mm, 18 982 h at 100 mm, and dropped to 16 816 h at 120 mm. For every 20 mm extension of the cantilever, the service life is reduced by about 2 500 to 2 800 hours. Changing the structure is more economical than changing the bearings.
variable | value | P(N) | L10h (hour, 6310) | Disposal recommendations |
|---|---|---|---|---|
Load factor fd | 1.0 | 7 764 | 144 932 | Smooth and continuous operation can take 1.0~1.2 |
Load factor fd | 1.3 | 10 093 | 65 968 | General values for gear transmission |
Load factor fd | 1.8 | 13 975 | 24 851 | Impact conditions, close to the lower limit of life |
Cantilever length | 60mm | 9 261 | — | Shortening the cantilever is a priority over replacing larger bearings |
Cantilever length | 120mm | 10 509 | — | Equipped with independent support or switch to double pivot structure |
The axial force of spur gears is zero, so the above example of P = Fr is sufficient. But when switching to a worm gear reducer , the worm axial force must be taken into account, P = X·Fr + Y·Fa; When ≤ e, take X = 1 and Y = 0. Missing the axial force calculation is a common reason for the short life of this type of machine. The output end of the cycloidal pinwheel reducer is jointly carried by the pinwheel pin and the output mechanism. The distribution law of the bearing reaction force is different from that of conventional cylindrical gears. When checking, the reaction force data given by the manufacturer should be substituted into the same set of life formulas.
Qualified lifespan does not mean that it can be installed. According to Table 2 of GB/T 275-2015 "Rolling Bearing Fits", the load size is divided by P/C: 6308 scheme P/C = 10 093 / 40 800 = 0.247, 6310 is 0.163, both are greater than 0.12, which is a heavy load. In this example, the inner ring rotates to bear the rotating load (belt drive shaft). According to Table 3, the inner ring should have an interference fit of k6/m6/n6. The outer ring static bearing has a fixed load of H7/G7 according to Table 4. The use of interference fit will compress the clearance. The clearance group of GB/T 4604.1-2012 must be checked at the same time, and relaxed to C3 if necessary. The tolerance level of the journal and seat hole is based on this standard: shaft IT6, hole IT7, journal cylindricity tolerance 2.5 μm, seat hole 2.5 μm (bearing tolerance level 0, d ≤ 50 mm).
step | action | criterion or output |
|---|---|---|
1 | Take the measured power and speed of the motor and calculate n2 and T2 | T2 = 9550·P1·i·η/n1 |
2 | Calculate Ft based on the final gear, check the cantilever load and supporting geometry | R_A, R_B support reaction force |
3 | Convert the equivalent dynamic load P to determine whether the axial force exists | P = fd·(X·Fr + Y·Fa) |
4 | Check the sample to get C and C0, first calculate L10h and then calculate s0 | L10h ≥ target value and s0 ≥ 1 |
5 | Determine the fit zone according to GB/T 275-2015, check the clearance and thermal clearance | Shaft IT6 / Hole IT7, clearance group |
The other three points need to be checked on site: first, when the gear reduction motor is supplied as a whole, the alignment deviation between the motor and the reducer will form an additional load, and the service life needs to be corrected according to the actual alignment data; second, if the bearing clearance is compressed too much due to interference, the operating temperature rise will be significantly amplified; third, if there is no relief structure for the thermal expansion of the shaft system, it is often not the gear but the bearing that is stuck.
Bearing life is not an additional check after selecting the reducer, but a part of the loop that must be closed when choosing a reducer. Use the formula of GB/T 6391-2010 to clearly calculate the three steps of "load-dynamic load-life", and then use GB/T 275-2015 to determine the fit and clearance. Only then will the life conclusion have engineering significance. The specific conclusion given by the calculation example in this article is: 18 982 h of 6308 under the same working conditions is not enough to reach the target of 25 000 h. The required dynamic load is back calculated to be 44.7 kN, which can be met by 6310; if the cantilever can be reduced from 100 mm to 60 mm, 6308 can also reach 24 572 h. It should be noted that the measured life of the prototype is usually lower than L10h. In important occasions, a margin of L10 should still be reserved and bench verification should be done.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?