WeiGao Transmission
Email: sales@wgt.net.cn
Language
通栏图2
tonglantu.jpg
Home / Products / Coupling / CSKA/CSKW universal joint

Product Search

Products Category

loading

Share to:
facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

CSKA/CSKW universal joint

SKU:
Availability:
Quantity:

The CSKA/CSKW universal joint is the FA factory-automation standard cross coupling for light-to-medium torque drives where two shafts cannot be held perfectly parallel — packaging, textile and printing machinery. CSKA is the single fixed-pin type: one cross, one bearing set, short and light. CSKW is the double fixed-pin type: two crosses back to back, absorbing angular misalignment and parallel offset together. Both are stocked over a 10–20 mm bore range, in alloy steel with 304 stainless steel for wash-down duty.

Typical Specifications of the CSKA/CSKW Universal Joint

Bore d (mm) Outside D (mm) Length L / LD (mm) Allowable Torque (N·m) Allowable Speed (r/min) Allowable Condition Variable Static Break Torque (N·m) Mass (g)
10 20 42 / 67.5 20.1 2000 80,000 83 55
12 23 52 / 83 33 1800 121,000 140 110
14 25 59 / 94.5 46 1600 151,000 200 155
16 32 74 / 117.5 76 1400 200,000 310 260
20 36 87 / 139 129 1000 273,000 530 465

WGT catalogue values. Allowable torque, speed, condition variable and static break torque are published for the single fixed-pin type CSKA; the double fixed-pin CSKW shares the same bore and D envelope, with LD = 67.5 / 83 / 94.5 / 117.5 / 139 mm and mass 95 / 180 / 250 / 390 / 690 g. Keyway is b JS9 on a d H7 bore, with a 4-M coarse thread (M5 or M6) service port. Rubber-bushed CSC and CSW versions cover the same bore range. Every order is re-checked against your actual duty.

Heavier cross-pin universal joints built to JB/T 5901 — the WX/WXD and WS/WSD small types and the WSS telescopic cardan shaft — carry 11.2–1120 N·m and up to 45° per joint, as does the SWC cardan shaft series. Above roughly 2000 r/min, ask for those.

Where This Universal Joint Is Used

  • Packaging machines: carton erectors, wrappers and case packers, where cam shafts are never perfectly aligned and the drive reverses every stroke.
  • Textile, winding and spinning machinery: high cyclic content with frequent direction reversal — the built-in bearing responds equally fast both ways.
  • Printing and web-handling equipment: registration rolls, tension rollers and dancer arms tolerating a small permanent offset.
  • Woodworking and light feeders: saw blades, knife shafts and dosing screws on panel lines.
  • Assembly and packaging robotics: small axis drives where a light joint keeps robot payload down — the CSKA at d = 16 mm weighs 260 g.
  • Food, chemical and pharmaceutical machinery: the 304 stainless build and CSC / CSW rubber-bushed versions for wash-down duty.

Selection Example: 1.5 kW Web-Handling Roll Drive

A printing line drives a tension roller from a 1.5 kW, 960 r/min motor through a cross universal joint. The roller shaft sits 10° out of line with the motor shaft and 8 mm off-axis, and the roll is re-threaded several times a shift — a reversing, intermittent duty.

1. Design torque. T = 9550 × P / n = 9550 × 1.5 / 960 = 14.92 N·m. The reversing duty carries a service factor of 1.3, so Tdesign = 19.4 N·m. The same factor carries into the upstream gear reducer selection and gearbox sizing.

2. Condition variable. WGT’s method combines speed, angle and torque into one check: condition variable = speed (r/min) × angle (°) × torque (N·m), which must stay below the allowable value for the size. Here 960 × 10 × 19.4 = 186,240. The allowable values are 80,000 at d = 10, 121,000 at d = 12 and 151,000 at d = 14 — all rejected; d = 16 mm gives 200,000 and is accepted.

3. Speed with angle coefficient. Permissible speed is derated by the misalignment angle: 1.00 below 5°, 1.05 at 10°, 1.18 at 15°, 1.43 at 20°, 1.82 at 25°, 2.50 at 30°. With 10° the coefficient is 1.05: 960 × 1.05 = 1008 r/min against an allowable 1400 r/min at d = 16 mm.

4. Torque and static margin. Allowable torque at d = 16 mm is 76 N·m against the 19.4 N·m design torque, a margin of 3.9×. The static break torque of 310 N·m is 16× the design load, so a jam shears the joint before it damages the shaft. Inertia is Gd² = 1.5 kg·cm² and mass 260 g.

5. Structure, and pairing with the reducer. The 8 mm parallel offset cannot be taken up by a single joint, so the double type is required: CSKW, d = 16 mm, LD = 117.5 mm, A = 43.5 mm, mass 390 g, Gd² = 2.3 kg·cm², static break torque 230 N·m. The bore is d H7 with a b JS9 keyway, and the reducer low-speed shaft bore and key must match. The sleeve bearing is built-in with a fixed pin, rated for 30° working angle and 45° extreme per joint.

That is one complete universal joint selection in five steps. Speed, angle, offset, duty cycle and environment all shift the answer, which is why universal coupling sizing is done against the real machine, not a catalogue cover. Any service factor gearbox quote should carry the same factor through to the joint, and the gearbox maintenance plan should include grease-port and cross-pin wear checks.

Get the Exact Model Online — Free Selection System

Open the WGT Motor & Gearbox Online Selection System, enter your power, input speed and required output speed or torque, and the system returns matching models with full technical data in seconds. Need a cross-reference against an imported WX, WSD, SWC or Japanese FA-standard joint? Send the type designation or a nameplate photo and our engineers will reply with the equivalent, price and lead time within 24 hours. Special bores and keyways are available on request.

Previous: 
Next: 

WeiGao Transmission

Weigao Gear Reducer is an alliance group company that integrates research and development, production, sales, and service

+86 400 801 9158

Email: sales@wgt.net.cn;wgt.net.cn@gmail.com
Tel:+86571 85023000

WEIGAO REDUCER

FEEDBACK