WeiGao Transmission
Email: sales@wgt.net.cn
Language
通栏图2
tonglantu.jpg
Home / News / How to ensure normal operation of WPDKS80-60 reducer worm gearbox after the load is reduced

How to ensure normal operation of WPDKS80-60 reducer worm gearbox after the load is reduced

Author: Site Editor     Publish Time: 16-10-2026      Origin: Site

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button
How to ensure normal operation of WPDKS80-60 reducer worm gearbox after the load is reduced

1. Lubrication system adaptation and optimization

‌Adjust the oil level to a reasonable range‌: Control the oil level at 1/2~2/3 of the oil level mirror to avoid excessive oil level under low load, causing abnormal rise in oil temperature, oil leakage, or insufficient oil level leading to insufficient lubrication of the worm gear meshing surface.

‌Optimize the oil change cycle‌: Under low load conditions, the oil oxidation rate slows down. The regular oil change cycle can be appropriately extended from 3000 to 5000 hours to 6000 hours. However, it is necessary to take samples every 300 hours to check the oil quality. If blackening, turbidity, foam or impurity precipitation appears, replace it immediately.

‌Select suitable oil‌: Continue to use L-CKD 220# extreme pressure gear oil to avoid mistakenly selecting low-viscosity oil due to low load, resulting in the inability to form an effective oil film on the sliding friction surface of the worm gear.

2. Operation parameter calibration matching

‌Lower the driving torque threshold‌: Adjust the torque limit parameter in the frequency converter to 1.2~1.5 times the actual load to avoid unnecessary impact wear caused by the large torque output under the original rated load, while retaining sufficient overload protection redundancy.

‌Check the input speed‌: Stabilize the input speed within 1500rpm. It is strictly prohibited to operate at extremely low speeds below 300rpm for a long time to prevent the sliding friction surface from forming a dynamic pressure oil film and the risk of dry wear.

‌Confirm motor matching‌: If the load decreases by more than 50%, replace the low-power adapted motor in time to avoid "big horse-drawn carts" causing low motor efficiency, output torque fluctuations, and affecting the smoothness of the worm gear box transmission.

3. Strengthen full-dimensional status monitoring

‌Normal temperature control‌: Use an infrared thermometer to monitor the box temperature every day to ensure that the shell temperature is ≤80°C, the bearing part is ≤70°C, and the temperature difference at the meshing point is controlled within 15°C. If the temperature rise rate exceeds 5°C/h, stop the machine immediately for investigation.

‌Vibration and abnormal noise inspection‌: Use a vibration meter to check the vibration speed every week to ensure that the vibration value is ≤7.1mm/s. Use a listening rod to monitor the meshing parts. If there are sharp friction sounds or uneven impact sounds, promptly check whether there are abnormal side clearances or local dry grinding problems.

‌Current Stability Monitoring‌: Record the motor operating current every day. The current fluctuation amplitude must be controlled within ±5% of the rated value to avoid transmission shock caused by abnormal current fluctuations under low loads.

4. Regular inspection of mechanical structure

‌Retest the meshing backlash‌: Use a dial indicator to check the worm gear meshing backlash every six months, and stably control the backlash within the standard range of 0.15~0.3mm to avoid reverse impact caused by too large a backlash under low load, or jamming and heating caused by too small a backlash.

‌Sealing and vent cap inspection‌: Check the end cover sealing ring every week for aging and cracking, and clean the vent cap once a month to prevent negative pressure and moisture absorption caused by changes in temperature difference between the inside and outside of the box under low load, and water vapor intrusion to aggravate component corrosion.

‌Retightening of anchors and couplings‌: Retighten all anchor bolts according to the specified torque (usually 80~120N·m), check whether the buffer parts of the elastic coupling are intact, and avoid low-frequency resonance caused by insufficient base stiffness under low loads.

Latest News

WeiGao Transmission

Weigao Gear Reducer is an alliance group company that integrates research and development, production, sales, and service

+86 400 801 9158

Email: sales@wgt.net.cn;wgt.net.cn@gmail.com
Tel:+86571 85023000

WEIGAO REDUCER

FEEDBACK