WeiGao Transmission
Email: sales@wgt.net.cn
Language
通栏图2
tonglantu.jpg
Home / News / How to calculate the fatigue life of reducer gears: GB/T 3480.6 Variable load Miner damage accumulation calculation example - Hangzhou Weigao Transmission

How to calculate the fatigue life of reducer gears: GB/T 3480.6 Variable load Miner damage accumulation calculation example - Hangzhou Weigao Transmission

Author: Site Editor     Publish Time: 08-11-2026      Origin: Site

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

Selection The rated torque, load coefficient, and tooth width modulus were all calculated, and the static check was also passed, but the gear was still pitted. The static check answer is "Can it withstand this moment?". Pitting corrosion is fatigue failure. The answer is "Will it break after a few years?" This article follows GB/T 3480.6-2018 "Calculation of load carrying capacity of spur gears and helical gears Part 6: Calculation of service life under variable load conditions" (equivalent to ISO 6336-6:2006), and uses a 30 kW reducer to go through the calculation example.

1. Life calculation and static verification are two questions

1.1 Three inputs, one is indispensable

GB/T 3480.6 stipulates that three things are required for the calculation of variable load life: stress spectrum, material fatigue characteristics, and damage accumulation method. The stress spectrum comes from the load spectrum, which divides the load range into several levels, and each level is assigned a number of cycles; the material fatigue characteristics come from the SN curve, that is, how many cycles the material can withstand under a certain stress; the damage accumulation method adds up the damage in each level to determine whether it exceeds the limit. The calculation formula is: the gear cycle number n i is divided by the allowable cycle number N i of the stress , and the sum is U.

1.2 The load factor should be taken as 1 here

During static calibration, K A is set to 1.00 to 2.00 or more according to the impact level, but when using the load spectrum method, K A must be set to 1.0. Section 5.2 of the standard is straightforward: the application factor is taken to be unity here, and the effects of all applied loads should be reflected by the stress levels factored into the method. Blockage and impact have appeared as independent gears, and multiplying them again will be counted twice. In the same way, of the torque of each gear must be used the upper limit in the calculation of classification, which is the requirement of Section 5.1.

2. Calculation example: One-year load spectrum of 30 kW reducer

2.1 Model and coefficients

The calculation example takes a two-stage spur gear reducer to drive a belt conveyor, and the final stage is the control condition.

project

symbol

value

unit

Basis and explanation

Motor power/speed

P 1 /n1

30/1 450

kW/r/min

4 pole asynchronous motor

Overall speed ratio/total efficiency

i/n

20(4×5)/0.96

—

Two-stage cylindrical gear

Output torque

T2

3 794

N·m

9550·P 1·i·η/n1

final gear

m/z 1 /z2

5/20/100

mm / tooth / tooth

d 1 = 100, d 2 = 500 mm

Tooth width

b

70

mm

ψd = 0.70

Pinion torque/speed

T 1 /n

759/362.5

N·m/r/min

F t = 15 175 N, v = 1.90 m/s

Elasticity/node area coefficient

Z E / Z H

189.8/2.5

√MPa / —

Steel pairing, straight teeth α = 20°

Coincidence

ε α ;Z ε / Y ε

1.70;0.875/0.690

—

Z ε =√((4−ε α )/3)

load factor

K

1.455

—

K V 1.15×K Hα 1.10×K Hβ 1.15, K A is 1

2.2 Load spectrum classification and stress spectrum

The load spectrum is classified according to the principle of Section 4.2: 64 gears are commonly used, wide gears in the low load section, narrow gears in the high load section, zero load gear is reserved, and the highest torque corresponds to the lowest numbered gear. The calculation example divides 6 000 h in a year into 6 gears. The number of cycles in each gear = the total number of cycles of the pinion × the time ratio. The total number of cycles is 362.5 × 60 × 6 000 = 1.305 × 10 8 times. The contact stress is calculated according to GB/T 3480.2-2021, σ H = Z H ·Z E ·Z ε ·√(2·K·T 1·(u+1)/(b·d 12·u)).

file number

Torque upper limit/rated torque of this gear

Time proportion

Number of cycles n i (times)

Torque Ti ( N·m)

Contact stress σ H,i (MPa)

0

0.00

8%

1.044×107

0

0

1

0.55

12%

1.566×107

417

599

2

0.90

40%

5.220×107

683

766

3

1.00

33%

4.307×107

759

807

4

1.70

6%

7.830×106

1 290

1 053

5

2.20

1%

1.305×106

1 669

1 198

2.3 SN curve and Miner accumulation

The material is 20CrMnTi carburized and quenched MQ grade, the tooth surface is 58~62 HRC, σ Hlim = 1 500 MPa. The SN parameters are in accordance with GB/T 3480.6 Table A.1 'No pitting corrosion' row of carburized and quenched steel: pitting corrosion Wöhler index p = 6.6112, N Lref = 50×10 6 times. The table indicates that p of pitting corrosion is given in terms of torque, and the conversion to stress needs to be doubled, so the allowable number of cycles in the stress domain is N i = N Lref ·(σ HG /σ H,i ) 2p , and the index 2p = 13.2224. σ HG is the allowable contact fatigue limit calculated according to the influence coefficient chain of GB/T 3480.2-2021, which is taken as 1 000 MPa. The curved side corresponds to p = 8.7378.

Gears with stress lower than σ HG do not cause fatigue damage, and the allowable number of cycles is regarded as infinite, because the SN curve is a horizontal section after passing the inflection point. The damage is calculated according to the Palmgren-Miner rule U = Σ n i /N i , and U ≤ 1 passes.

file number

Contact stress σ H,i (MPa)

Relationship with fatigue limit

Allowed number of cycles N i (times)

Damage share n i /N i

0~3

0~807

below fatigue limit

no damage

0.0000

4

1 053

Exceed 5.3%

2.53×107

0.3089

5

1 198

Exceeded by 19.8%

4.61×106

0.2831

Total damage U

0.5921

U = 0.5921 is less than 1, and the operation is qualified based on the load spectrum of 6 000 h per year; extrapolated according to the same spectrum, the total life is 6 000 / 0.5921 ≈ 10 134 h, which is 1.69 years.

3. What is eating up your lifespan?

3.1 No damage will occur 90% of the time

Rated and below (gear 0 to 3) account for a total of 93% of the operating time and contribute zero to the pitting life ; the remaining 7% of the plugging and emergency stop overload time contribute 100% of all damage, with the plugging gear accounting for 52.2% and the emergency stop gear accounting for 47.8%. Compared with the baseline life of 10 134 h, the blockage elimination gear is increased to 21 191 h, and the emergency stop gear is 19 421 h.

This explains why 'it runs well most of the time, but there are still pits on the tooth surface' - the damage comes from the 7%. Special attention should be paid to the hard tooth surface reducer : the carburizing and quenching tooth surface will not improve the running fit like the soft tooth surface.

3.2 Three levers and backcalculation

Change parameters

Value and corresponding U

required to achieve U = 1

Tooth width b (mm)

55→2.92; 60→1.64; 65→0.97; 70→0.59; 80→0.12

64.7mm

Allowable contact fatigue limit σ HG (MPa)

900→2.38; 950→1.17; 1 000→0.59; 1 050→0.31; 1 100→0.080

961MPa

The proportion of blocking time

2%→0.386; 4%→0.489; 6%→0.592; 8%→0.695; 10%→0.798; 12%→0.901

13.9%

Overall magnification of load spectrum

1.00; 1.05→0.817; 1.08→0.985; 1.15→1.492

1.08

The efficiencies of the three levers are not equal: for every 5 mm increase in tooth width, U decreases geometrically; σ HG is restricted by hardness, viscosity, roughness, and size coefficient, and is more difficult to improve than tooth width; when the proportion of plugging material increases from 6% to 12%, U only rises from 0.592 to 0.901. Although it is effective to control plugging, it is not as solid as the tooth width and material margin.

When the load spectrum is amplified as a whole, the damage is strictly proportional to k p , and the amplification factor has an analytical solution (1/U) 1/p , which is consistent with the numerical iteration to four decimal places. This 1.08 reminds us: if the on-site working conditions are more than 8% worse than the design assumptions, the service life will be lost. This is not difficult to achieve under blocking and sticking conditions. The equivalent torque method can also give the application coefficient: According to the formula T eq = (Σn i T i p /Σn i ) 1/p in Appendix A , the calculation example is 948 N·m, corresponding to K A = 1.25. However, the standard also indicates that this simplified formula is unsafe when the number of cycles is large, and the formal calculation should be based on gear-by-gear accumulation.

There is also a static check to be made. Section 5.1 of the standard makes it clear that the highest stress within the design life still needs to be calibrated with a safety factor based on static strength, and the stress may come from extreme instants outside the load spectrum. The maximum instantaneous rated torque of the calculation example is 2.20 times the rated torque, the contact stress is 1 198 MPa, and the static safety factor S H = 1 500 / 1 198 = 1.25, which is qualified. Under the same working condition, the tooth root bending stress is 416 MPa. According to the allowable value of 307 MPa in GB/T 3480.3, the safety factor is 0.74, which is less than 1 - indicating that the most extreme instant is controlled by bending and must be cut off by overload protection.

4. Selection and troubleshooting steps

step

do what

Output and error prone points

1 Get the load spectrum

The measured shaft torque or current signal is divided into different levels, and the zero load level is reserved.

For the upper limit and number of cycles of each gear, do not use equivalent torque instead.

2 Calculate stress spectrum

Calculate σ step by step according to GB/T 3480.2 and GB/T 3480.3H,i and σ F,i

Using the torque upper limit, K A takes 1

3. Set SN parameters

Select p and N according to Table A.1 Lref , and determine σ HG

The pitting corrosion p is doubled when converted to stress.

4 cumulative damage

U = Σ n i /N i , gears below the fatigue limit are not counted.

U ≤ 1 means passing, and it depends on the damage attribution

5 Iteratively find the safety factor

Adjust S iteratively according to Section 5.4. It cannot be inferred from U.

Large and small gears, bending and pitting are calculated separately

6 Calibration of extreme instantaneous

Calculate the safety factor based on the static strength for the highest stress within the design life.

More than 10 3 cycles must rely on overload protection

This algorithm can be used in reverse for on-site inspections. If there are pitting or shallow peeling on the tooth surface, first check the high gear of the load spectrum: blocking, sticking, frequent starts and stops, soft feet, and check whether σ H,i exceeds the fatigue limit step by step; if the tooth is broken or chipped, check the bending side and modulus of the tooth root. The algorithm in this article is not applicable to cycloid pinwheels and worm gear reducers: cycloid pinwheels are assessed according to GB/T 36491-2018, worm gears are assessed according to GB/T 10085-2018 and GB/T 10089-2018, and gear reduction motors are the same as this article.

in conclusion

The gear life under variable load can be calculated clearly, provided that the load spectrum, SN curve, and damage accumulation are put together. The calculation example is worth remembering: for a 30 kW reducer that has passed static calibration, 93% of the running time contributes zero to the pitting life, and all damage comes from 7% of plugging and emergency stop overload. The total damage U = 0.5921, corresponding to 1.69 years of rated load spectrum life; the tooth width is reduced to 64.7 mm and is still within the qualified boundary, and the load spectrum is enlarged by 8% and crosses the boundary. Compared with 'Place an order if the torque is right', this algorithm asks one more question: How many times a year will overload occur? Hangzhou Weigao Transmission provides product lines such as hard tooth surface reducers, 、cycloid pinwheel reducers, 、worm gear reducers , and gear reduction motors . The service life can be calculated and consulted based on the measured load spectrum.

Latest News

WeiGao Transmission

Weigao Gear Reducer is an alliance group company that integrates research and development, production, sales, and service

+86 400 801 9158

Email: sales@wgt.net.cn;wgt.net.cn@gmail.com
Tel:+86571 85023000

WEIGAO REDUCER

FEEDBACK