Author: Site Editor Publish Time: 10-11-2026 Origin: Site
1. Preparation work before cleaning
Preparation tools: soft nylon brush, dust-free cloth, dry compressed air gun (pressure ≤ 0.3MPa), oil pan, and torque wrench.
Material selection: Priority is given to neutral gearbox cleaning agents. Kerosene/diesel can also be used instead. Strong acids, alkalis, and highly volatile gasoline are prohibited.
Mark all assembly points in advance to avoid misalignment during reassembly. Used oil and waste cleaning agents should be collected and handed over to qualified agencies for disposal.
2. Completely drain the old oil
When the oil temperature is still warm after the equipment is shut down, open the oil drain plug at the bottom and remove the breather plug to speed up oil drainage.
Observe the state of the discharged old oil. If it contains a large amount of metal debris, is emulsified and turns white, it indicates serious internal wear or water intrusion, and subsequent inspection is required.
After the oil is completely drained, use a dust-free cloth to wipe the remaining oil at the oil drain port to prevent residual impurities from contaminating the new oil.
3. System circulation pre-flushing
Inject 1/3 of the tank"s capacity of cleaning oil into the box, and turn it manually for 3 to 5 turns to allow the oil to cover all meshing surfaces.
Run at low speed for 5 to 10 minutes without load, use gear agitation to dissolve sludge and metal debris, and then completely drain the flushing oil.
If the discharged oil is still turbid and black, repeat the cycle of flushing 1 to 2 times until there are no obvious impurities in the discharged liquid.
4. Deep cleaning of internal components
Open the observation hole or the box cover, and use a soft brush to gently brush the stubborn sludge on the tooth surface and the inner wall of the box along the gear rotation direction. Do not brush hard in the opposite direction to damage the tooth surface.
Precision parts such as bearings and oil guide grooves should be soaked in detergent for 10 minutes and then cleaned with a soft brush. It is strictly forbidden to use wire brushes or sandpaper to scrape the surface.
The oil passages and oil return holes are purged and cleared with 0.2MPa compressed air to ensure that there is no clogging residue.
5. Drying and residue verification
Use dry, oil-free compressed air to completely purge the inside of the box, focusing on drying the bearing gaps, corners of the box and other areas prone to fluid accumulation.
Ventilate and let it sit for more than 30 minutes to confirm that there are no cleaning agent residues and no traces of moisture in the box to prevent subsequent damage to the lubrication performance of the new oil.
Simultaneously check that there are no pitting cracks on the gear tooth surface, that the bearing clearance meets the standards, that the seals have no aging and deformation, and that failed parts are replaced directly.
6. Verification after reassembly and cleaning
Reset all components according to the marks, apply a small amount of sealant evenly on the sealing surface, and tighten the bolts in diagonal order three times to the standard torque.
Replace the lubricating oil filter element with a new one, and add the appropriate N220/N320 medium-load industrial gear oil to the center line of the oil window.
Manually turn the machine for several turns to confirm that there is no jamming. Run without load for 5 minutes to recheck the oil temperature, vibration, and sealing points for leakage. After confirming that the machine is qualified, it will be put into normal working conditions.
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?
Fertilizer Plant Gearbox: Turnaround Season Demand and Sizing Guide