Author: Site Editor Publish Time: 10-11-2026 Origin: Site
1. Static accuracy verification
Foundation level is up to standard: Use a level with an accuracy of 0.02mm/m to detect the longitudinal and transverse leveling of the top of the box. Control the error by adjusting the gasket to ≤0.05mm/m. There is no hanging gap between the base and the foundation.
Shafting alignment qualified: Use a dial indicator to measure the radial deviation between the input shaft and the motor shaft ≤0.1mm, the end face runout ≤0.05mm; the coaxiality deviation between the output shaft and the load shaft ≤0.15mm.
All fasteners are locked: Use a torque wrench to tighten the anchor bolts in diagonal order. The torque is controlled at 80-120N·m. All connecting bolts are not loose or falsely locked.
Transmission parts are installed in place: Sprockets, gears and other transmission parts on the output shaft are pressed into place using assembly fixtures. It is strictly prohibited to knock them, and they should be installed as close to the bearing as possible to reduce shaft extension bending stress.
2. Manual turning inspection
Disconnect the motor power supply and manually rotate the input shaft. The whole process of rotation is flexible, without stagnation or frustration, and the forward and reverse turning feels even and consistent.
There is no abnormal scratching sound in the meshing of the worm gear, and there is no abnormal metal impact sound during the turning process. The backlash angle complies with the design standards of this model and there is no obvious gap.
The output shaft rotates synchronously and smoothly with the input shaft, without slipping or jamming, and there is no additional resistance in the entire transmission chain.
3. No-load test run verification
It runs continuously for more than 2 hours without load, and the whole operation is smooth, without impact or abnormal vibration. The double amplitude of vibration in the middle part of the casing is ≤0.05mm.
The running sound is a uniform and soft "buzzing" sound, without sharp metal scraping sounds, periodic impact sounds or high-frequency howling sounds.
There is no oil leakage at each sealing point and the joint surface of the box. Only a trace amount of oil film is allowed to infiltrate the oil seal lip.
The temperature of the bearing seat is ≤75℃, the difference between the oil temperature in the oil pool and the environment is ≤35℃, and there is no local overheating.
After the test run, all fasteners were not loose, and the oil level was stable at 1/2~2/3 of the height of the oil window, with no abnormal changes.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?