Author: Site Editor Publish Time: 10-11-2026 Origin: Site
Most of the markings on the worm gear reducer samples are center distance, speed ratio and output torque. What really determines whether this transmission is good or not is two numbers that few people write down: the relative sliding speed v s of the tooth surface and the sliding rate ν. Sliding speed determines heat generation and wear, and sliding rate determines efficiency. There is no need to consult the manual for these two numbers. They can be determined by the three geometric parameters of the module, the diameter of the worm graduation circle, and the number of worm heads. This article completes this calculation chain according to GB/T 10085-2018 'Basic Parameters of Cylindrical Worm Transmission' and GB/T 10088-2018 'Cylindrical Worm Module and Diameter', and gives a complete calculation example of a 5.5 kW, 20:1 reducer.
Worm transmission is a spatial staggered shaft transmission, and the shaft intersection angle is usually 90°. When meshing, the circumferential speed v of the worm indexing circle 1 and the circumferential speed v of the worm gear indexing circle 2 are perpendicular to each other. The contact point is not pure rolling, but rolling and sliding coexist. The two velocity vectors are perpendicular, and the relative velocity of the contact point is the tooth surface sliding velocity:
v s = √(v 12 + v 22) = v 1/cos γ = v 2/sin γ
In the formula, γ is the lead angle on the worm indexing cylinder, which 1 is determined by the diameter coefficient q and the number of heads z: tan γ = z 1/q = z 1·m/d 1. And because v 1/v 2 = i·d 1/d 2 = 1/tan γ, the above formula is often written as v s = v 1/cos γ.
Divide the sliding speed by the linear speed of the worm gear indexing circle to get the sliding rate ν = v s /v 2 = 1/sin γ. The meaning of ν is how much distance the worm gear edge actually slides on the tooth surface for every unit distance it travels; ν equal to 1 means pure rolling. Ordinary cylindrical gear transmission is pure rolling contact, ν is 0; worm transmission ν usually falls between 2 and 16. In contrast, the cycloidal pinwheel reducer relies on the simultaneous meshing of multiple teeth to share the load, and the hard tooth surface reducer relies on pure rolling contact, so the sliding ratio is very low. The efficiency shortcoming of the worm drive is rooted in this number.
Number of worm heads z1 | Diameter coefficient q | tan γ tangent value | Lead angle γ (°) | sin γ sine value | Sliding rate ν = 1/sin γ |
|---|---|---|---|---|---|
1 | 8.0 | 0.1250 | 7.13 | 0.1240 | 8.06 |
1 | 10.0 | 0.1000 | 5.71 | 0.0995 | 10.05 |
1 | 16.0 | 0.0625 | 3.58 | 0.0624 | 16.03 |
2 | 10.0 | 0.2000 | 11.31 | 0.1961 | 5.10 |
2 | 12.6 | 0.1587 | 9.02 | 0.1568 | 6.38 |
4 | 8.0 | 0.5000 | 26.57 | 0.4472 | 2.24 |
Table 1 illustrates two things: as the number of heads increases from 1 to 4, the sliding rate can be reduced from 16.03 to 2.24; and the larger q (the larger the relative modulus of the worm pitch circle diameter), the smaller the lead angle and the larger the sliding rate, which is the price of exchanging worm stiffness.
The calculation example takes a worm gear reducer that drives a belt conveyor. The motor has 4 poles, n 1 = 1450 r/min, and the input power P 1 = 5.5 kW. The geometric parameters are selected according to GB/T 10088-2018: module m = 4 mm (priority series), worm graduation circle diameter d 1 = 40 mm. Take z 1 = 2, z 2 = 40.
project | symbol | numerical value | unit | Basis and explanation |
|---|---|---|---|---|
Modulus | m | 4 | mm | GB/T 10088-2018 Table 1 Priority Series |
Worm pitch circle diameter | d1 | 40 | mm | GB/T 10088-2018 Table 2 |
Diameter coefficient | q=d 1/m | 10.0 | — | Limit the number of hobs and standardize the values |
Number of worm heads/number of worm gear teeth | z 1 /z2 | 2/40 | — | z 2 takes 28~70 as the common range |
Transmission ratio | i = z 2/z1 | 20 | — | GB/T 10085-2018 Priority speed ratio |
Worm gear pitch circle diameter | d 2 = z 2·m | 160 | mm | Standard drive, x 2 = 0 |
center distance | a = (d 1+d 2)/2 | 100.0 | mm | GB/T 10085-2018 recommended center distance value |
Output speed | n 2 = n 1/i | 72.50 | r/min | — |
The worm gear indexing circle linear speed v 1 = π·d 1·n 1/60000 = 3.0369 m/s, the worm gear indexing circle linear speed v 2 = π·d 2·n 2/60000 = 0.6074 m/s. The ratio of the two, 5.0000, is consistent with 1/tan γ = 5.0000, indicating that the geometric parameters are self-consistent.
Lead angle γ = arctan(z 1/q) = arctan(0.2) = 11.31°, sin γ = 0.1961, cos γ = 0.9806. Substituting in, we get v s = v 1/cos γ = 3.0970 m/s ( 2checked with v /sin γ, the same is 3.0970 m/s), and the sliding rate ν = v s /v 2 = 1/sin γ = 5.10.
The meshing efficiency is approximated by a spiral pair: η 1 = tan γ / tan(γ + ρ v ), ρ v is the equivalent friction angle, which is related to the worm gear material, worm tooth surface hardness and sliding speed v s . Look up the table and find that v s = 3.10 m/s corresponds to ρ v = 1°35′~1°59′. When the hardened and ground worm is well lubricated, take the small value. Substitute it and get η 1 = 0.8741 (take the small ρ v ) ~ 0.8468 (take the large ρ v ).
The total efficiency must be multiplied by the bearing efficiency and oil churning efficiency. The textbook takes η 2= 3 0.95~0.96, so η = 0.8045~0.8392, taking 0.8217. This result falls near the upper edge of the closed worm transmission experience range given in the textbook based on the number of heads ( 1 eta is about 0.75~0.82 when z = 2), and the calculation formula is self-consistent with the estimate.
calculated item | formula | result |
|---|---|---|
Lead angle | γ = arctan(z 1/q) | 11.31° (11°19′) |
sliding speed | v s = v 1/cos γ | 3.0970m/s |
slip rate | ν = 1/sin γ | 5.10 |
Equivalent friction angle | Table interpolated according to v s = 3.10 m/s | 1°35′~1°59′ |
meshing efficiency | η 1 = tan γ / tan(γ + ρ v ) | 0.8741~0.8468 |
total efficiency | η = 0.95~0.96 · η1 | 0.8045~0.8392, take 0.8217 |
Output power | P 2 = P 1·n | 4.520kW |
Output torque | T 2 = 9550·P 2/n2 | 595.3N·m |
Heating power | P s = P 1(1−η) | 0.9804 kW, accounting for 17.8% of the input |
All this 0.98 kW becomes heat in the box.
v s = 3.0970 m/s This gear directly determines the material of the worm gear ring gear. The teaching materials are available in three levels according to the sliding speed:
Worm gear ring gear material | Applicable sliding speed v s (m/s) | Material properties and applicable occasions |
|---|---|---|
Gray cast iron HT150/HT200 | ≤ 2 (HT200 can reach 2~2.5) | Low strength and poor friction reduction, only used for low speed, light load or unimportant transmission |
Aluminum iron bronze ZCuAl10Fe3 | ≤ 4 | Its anti-gluing ability is weaker than that of tin bronze, but it has high strength and low price. It is used for medium sliding speeds. |
Cast phosphor tin bronze ZCuSn10P1 | ≤ 25 | It has good friction-reducing, wear-resistant and anti-gluing properties, lower strength and more expensive price. It is used for high-speed or important transmissions. |
This example falls into the aluminum-iron-bronze range. The allowable contact stress also follows v s : ZCuAl10Fe3 with quenched steel worm, when v s = 3 m/s, it is 180 MPa, when v s = 4 m/s, it drops to 160 MPa, and when interpolated to 3.0970 m/s, it is about 178 MPa. Every time the sliding speed increases by one level, the allowable stress decreases by one level. This is a linkage relationship that is easily missed in Selection.
The thermal balance condition of the closed worm drive is t 1 = 1000·P 1(1−η)/(K t ·A) + t 0 ≤ [t] p , otherwise the oil temperature will continue to rise, the viscosity will drop, the lubrication will deteriorate, and the bonding will intensify. A is the heat dissipation area of the box (the area of the flange and heat sink is calculated as 50%), K t is the heat dissipation coefficient, [t] p is generally 60~70°C, with a maximum of not exceeding 90°C, and the ambient temperature t 0 is 20°C. Inverse solution: required heat dissipation area A ≥ 1000·P s /(K t ·([t] p − t 0)):
Heat dissipation conditions | Heat dissipation coefficient K t | Allowable oil temperature [t] p (℃) | Required heat dissipation area A (m²) |
|---|---|---|---|
Good natural ventilation | 14 | 60 | 1.751 |
Good natural ventilation | 14 | 70 | 1.401 |
Good natural ventilation | 17.5 | 60 | 1.401 |
Good natural ventilation | 17.5 | 70 | 1.120 |
Poor ventilation | 8.7 | 60 | 2.817 |
Poor ventilation | 10.5 | 60 | 2.334 |
Install shaft end fan | 20 | 60 | 1.226 |
Install shaft end fan | 28 | 60 | 0.875 |
It takes about 1.1~1.8 m² with good ventilation, and 1.9~2.8 m² with poor ventilation. When the space cannot be accommodated, the textbook gives three options: install additional heat sinks, install a fan at the end of the worm shaft, and install a serpentine cooling pipe in the oil pool. Installing a fan is particularly effective because the worm shaft rotates at a high speed. When K t is raised to 20~28, the heat dissipation area requirement drops to 0.875 m².
Put the above chain into executable order:
1. Determine the center distance and speed ratio. Select a and i according to the recommended values of GB/T 10085-2018. The speed ratio is preferably 10, 20, 40, or 80; the number of worm gear teeth z 2 in power transmission is generally 28 to 70. If it exceeds 80, the gear teeth will be bent and broken.
2. Number of fixed heads and diameter coefficient. z 1 Commonly used are 1, 2, and 4. Reverse self-locking is required to be 1, and efficiency and high speed are required to be the larger value; q Pair with the module according to Table 2 of GB/T 10088-2018.
3. Calculate the lead angle and sliding rate. tan γ = z 1/q, ν = 1/sin γ, ν is obviously too large, indicating that the number of heads is low.
4. Calculate the sliding speed and determine the material. v s = π·d 1·n 1/(60000·cos γ), select the worm gear ring gear material according to which gear v s falls in.
5. Check the equivalent friction angle to calculate the efficiency and determine the output capacity. η 1 = tan γ/tan(γ + ρ v ), multiply by 0.95~0.96 to get the total efficiency, and then calculate the output torque. These steps are also applicable to complete machine-supplied products such as gear reduction motors.
6. Do a heat balance check. Find the required heat dissipation area A. If it is not enough, add a heat sink or fan.
The on-site investigation goes in the opposite direction: the measured efficiency is obviously lower than the calculated value. First check whether v s exceeds the material grade and whether the value of ρ v is optimistic (whether the worm tooth surface has been ground and whether the lubrication is sufficient), then check whether q has been increased for stiffness; if the temperature rise is too high, check whether K t is close to the actual ventilation conditions and whether the flange is missing when converting the heat dissipation area, and then check the oil level and oil quality. This set of procedures can be directly used in the Selection docking of Hangzhou Weigao Transmission.
The slip rate ν is a total parameter of the worm gear reducer: it is completely determined by the geometric parameters, and also controls the meshing efficiency, heating power, worm gear material gear and required heat dissipation area. Calculate q, z 1, v s and ν clearly first, then check the efficiency and select materials, Selection no longer rely on trial and error.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?