Author: Site Editor Publish Time: 21-10-2026 Origin: Site
Prepare tools and materials
Special tools: bearing tensioner, copper rod, dial indicator, feeler gauge, torque wrench, gasket thickness gauge
Consumables: original bearings of the same model, NLGI level 2 extreme pressure lithium grease, L-CKD 220# extreme pressure gear oil, waterless cleaning agent, new skeleton oil seal, corresponding thickness adjustment gasket
3. TP series reducer bearing replacement steps
1. Disassembly and preprocessing
Disconnect the input and output couplings, lift the reducer from the base to a special workbench, clean the oil on the casing, and mark the original assembly positions of each end cover and gasket to avoid misalignment during reassembly.
2. Disassembly of old bearings
First remove the bearing end caps at both ends, use a bearing puller to hook the outer ring of the bearing and apply even force to pull it out. Do not directly knock the shaft body. If the bearing is rusty, partially heat the inner ring of the bearing to 80~100°C and pull it out quickly while it is hot to avoid annealing deformation of the journal.
3. Inspection of shaft and seat hole
Clean the journal and bearing seat hole, and check that the mating surface is free of roughening and wear, that the journal circular runout is ≤0.01mm, and that the seat hole has no cracks and deformation; if the journal wear exceeds 0.02mm, it needs to be repaired by brush plating before assembly.
4. New bearing installation
The new bearing is placed in lubricating oil at 80~100℃ and heated at a constant temperature for 10 minutes in advance. While it is hot, it is quickly inserted into the shaft shoulder for positioning. Use a copper rod to pad the inner ring of the bearing and evenly tap and press it into place. It is strictly forbidden to tap the outer ring to cause damage to the raceway.
5. Precise gap adjustment
Install the bearing end cover, and control the axial clearance of the worm shaft bearing at 0.01~0.02mm and the axial clearance of the output end bearing at 0.02~0.08mm by increasing or decreasing the adjustment shim between the end cover and the box body. There will be no jamming of the shaft body throughout the whole process.
6. Reassembly and trial operation
Reset each seal, end cover and connecting piece according to the mark, add lubricating oil of the designated brand, manually turn the bearing 3 times to confirm there is no obstruction, run without load for 30 minutes, monitor the bearing temperature rise ≤35℃, and there is no abnormal sound, and then gradually load it to the rated operating condition.
4. Core installation precautions
1. Fit tolerance control: The inner ring of the bearing and the journal adopt an interference fit, and the interference amount is 0.01~0.03mm; the outer ring and the seat hole adopt a transition fit, and the phenomenon of outer ring running is strictly prohibited.
2. Lubrication and filling specifications: The cavity of a single set of bearings should be filled with grease at a ratio of 1/3 to 1/2. Excessive use will cause the bearing to overheat and leak oil. Mixing of different brands of grease is strictly prohibited.
3. Shaft alignment requirements: The radial deviation between the input shaft and the motor shaft is ≤0.02mm, and the angular deviation is ≤0.02°. Elastic couplings are preferred, and rigid connections are prohibited from introducing additional loads.
4. Contact spot verification: After assembly, check the worm gear meshing contact area. The contact spots are not less than 70% in height and width. The contact area is biased towards the tooth surface entrance side to avoid early failure of the bearing caused by unbalanced load.
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?
Fertilizer Plant Gearbox: Turnaround Season Demand and Sizing Guide