Author: Weigao Transmission Publish Time: 22-09-2021 Origin: 威高传动
Among the many types of reducers, the worm gear reducer is a common reducer.The worm gear reducer is a power transmission mechanism that uses a speed converter of gears to reduce the number of revolutions of the electric motor (electric motor) to the required number of revolutions and obtain a larger torque.It is mainly composed of transmission parts, worm gears, shafts, bearings, boxes and accessories.It can be found in the transmission system of various machinery, from ships, automobiles, locomotives for vehicles, heavy machinery and tools for construction, processing tools and automatic production equipment used in the machinery industry, to ordinary household appliances, clocks and watches in daily life.Its applications range from large power transmission jobs to small loads, precise angular transmission can see the application of reducers, and in industrial applications, reducers have the function of reducing speed and increasing torque.Therefore, it is widely used in speed and torque conversion equipment.
picture
The basic structure of the worm gear reducer is mainly composed of transmission parts, worm gears, shafts, bearings, boxes and accessories.It can be divided into three basic structural parts: box body, worm gear, bearing and shaft combination.The case is the basis of all accessories in the worm gear reducer.It is an important accessory to support and fix the shafting parts, ensure the correct relative position of the transmission parts, and support the load acting on the reducer.The worm gear is mainly used to transmit motion and power between two interlaced shafts, and the bearings and shafts are mainly used to transmit power, run and improve efficiency.
Worm gear reducer knowledge
efficiency
Due to the large sliding friction loss of the worm gear reducer, compared with the helical gear, the bevel gear hard tooth surface reducer has a large loss and low efficiency, which is mainly determined by the following factors:
Helical gear worm stage transmission ratio
input speed
The efficiency of the worm gear reducer designed by Risco is obviously higher than that of a single-stage worm gear reducer, and its efficiency is only possible with a worm gear reducer with a large speed ratio η<0.5.
self-locking condition
Helical gear and worm gear plus reverse torque will produce reverse efficiency η'= 2-1/η, its value is obviously smaller than positive efficiency η, if positive efficiency η≤0.5, the worm gear reducer will self-lock. Only a few large speed ratio worm gear reducers The machine has a static self-locking function.If you need to use the self-locking brake effect, please consult our company
Early stage of operation
Because the tooth surface of the new worm gear reducer is not smooth enough, the friction angle is large, and the efficiency is smaller than that in normal operation.This effect is more pronounced when the transmission ratio is large.
stirring loss
In some installation positions, the first stage pinion is completely immersed in oil.For a reducer with a large number of seats and a reducer with a high input speed, the stirring loss will rise sharply, which cannot be ignored.Therefore, in case of such a situation, please consult our company Demai Transmission.
picture
Features of worm gear reducer
1. The structure of the worm gear reducer is very compact, the volume is also very light, and the shape is relatively ingenious.It has the characteristics of small size but high efficiency, good heat dissipation, and good heat exchange.
2. The installation of the worm gear reducer is also relatively simple.It has the characteristics of flexibility, and the worm gear reducer also has the advantage of convenient maintenance.Its advantages also include smooth transmission, low noise and durability.It is a good product we choose.
3. The worm gear reducer also has the characteristics of large output torque.It also has high security and reliability, which is of great benefit to our use.
Common Problems and Solutions
Common faults of worm gear reducer
1. The reducer heats up and leaks oil.In order to improve the efficiency of the worm gear reducer, non-ferrous metals are generally used as the worm wheel, and the worm is made of harder steel.Due to the sliding friction transmission, more heat will be generated during operation, resulting in different thermal expansion coefficients between the various parts of the reducer and the seals, resulting in gaps between the mating surfaces.Lubricating oil becomes thinner due to temperature rise, which is easy to cause leakage.
There are four main reasons for this situation: first, unreasonable material matching; second, poor surface quality of the meshing friction surface; third, incorrect choice of lubricating oil addition; fourth, poor assembly quality and use environment.
2. Worn worm gear.Worm gears are generally made of tin bronze.The matching worm material is quenched with 45 steel to hrc4555 or 40Cr to hrc5055, and then ground to roughness Ra0.8μm with a worm grinder.The reducer wears very slowly during normal operation, and some reducers can be used for more than 10 years. If the wear speed is fast, it is necessary to consider whether Selection is correct, whether it is overloaded, and the material, assembly quality or use environment of the worm gear.
3. The transmission pinion is worn out.It usually occurs on a vertically installed reducer, and it is mainly related to the amount and type of lubricating oil added.When installed vertically, it is easy to cause insufficient lubricating oil.When the worm gear reducer stops running, the transmission gear oil between the motor and the reducer is lost, and the gears cannot get proper lubrication protection.When the reducer is started, the gears cannot be effectively lubricated, causing mechanical wear or even damage.
4. The worm gear bearing is damaged.In case of failure, even if the gearbox is well sealed, it is often found that the gear oil in the reducer is emulsified, and the bearings are rusted, corroded, and damaged.This is because after the reducer has been running for a period of time, the condensed water generated after the temperature of the gear oil rises and cools is mixed with water.Of course, it is also closely related to bearing quality and assembly process.
troubleshooting
1. Guarantee the assembly quality.Some special tools can be purchased or homemade.When disassembling and assembling parts of the reducer, try to avoid hitting with tools such as hammers; when replacing gears, worm gears, and worms, try to use original accessories and replace them in pairs; when assembling the output shaft, pay attention to tolerance fit; use anti-sticking agent or red lead Oil protects the hollow shaft from wear, rust or scale in the mating area and is not easily disassembled during maintenance.
2. Selection Lubricants and additives.Worm gear reducers generally use 220# gear oil.For worm gear reducers with heavy loads, frequent starts, and poor operating environments, some lubricating oil additives can be selected to make the gear oil still adhere to the gear surface when the reducer stops running, forming a protective film to prevent heavy loads, low speeds, and during startup. high torque and direct metal-to-metal contact.The additive contains sealing ring conditioner and anti-leakage agent, which keeps the sealing ring soft and elastic, and effectively reduces the leakage of lubricating oil.
3. The installation position of the worm gear reducer is Selection.If the location permits, try not to use vertical installation.In vertical installation, the amount of lubricating oil added is much larger than in horizontal installation, which may easily cause heat generation and oil leakage of the reducer.
4. Establish a good lubrication and maintenance system.The reducer can be maintained according to the 'five determinations' principle of lubrication work, so that each reducer can be checked regularly by the person in charge.If the temperature rises significantly, exceeding 40°C or the oil temperature exceeds 80°C, the oil quality declines, or if there is a lot of copper powder and abnormal noise in the oil, stop the machine immediately, repair it in time, and eliminate it.replace.Pay attention to the amount of oil when refueling to ensure that the worm gear reducer is properly lubricated.
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?
Fertilizer Plant Gearbox: Turnaround Season Demand and Sizing Guide
How to judge whether the WP series worm gear reducer is installed in place
How to clean the lubrication system of QJR-D450-20-IX gear reducer
What is the function of the breathable cap of the ZD80-5-2 soft tooth surface gear reducer?
Tissue Machine Yankee Drive Gearbox: Sizing High-Inertia Paper Drives
Wastewater Treatment Gearbox Market 2027: Policy Deadlines and Screw Pump Sizing
Vertical Turbine Pump Gear Drive Selection: Thrust Load, Support and Bearing Life