Author: Site Editor Publish Time: 23-10-2026 Origin: Site
1. Preliminary judgment without disassembly (daily inspection stage)
This step does not require dismantling the equipment, and quickly locks the abnormal signs of the output shaft through the operating status:
1. Operating noise characteristics: There is a periodic "clunking" impact sound synchronized with the shaft speed at the output shaft end, or a continuous rustling sound of metal friction; after the load is disconnected and the no-load operation is performed, the abnormal sound is still concentrated at the output end, eliminating the interference of gear meshing noise.
2. Abnormal vibration performance: Touch the output end bearing end cover lightly with the back of your hand, and you can feel obvious periodic vibration; use a vibration meter to measure the radial vibration speed, and the value exceeds 7.1mm/s, far exceeding the ≤4.5mm/s standard for normal operation of the ZDY series reducer.
3. Abnormal temperature increase: The temperature of the output shaft bearing continues to exceed 80℃, and the factors of insufficient lubrication and bearing failure are excluded, indicating that journal wear leads to a sharp increase in friction resistance.
4. Abnormal operating performance: The input operation of the reducer is normal, but the output torque is obviously insufficient, the speed is lost, and the output shaft even briefly idles and slips after being loaded.
2. Accurate verification of tools (downtime and power outage stage)
After the power is cut off and the machine is locked, evidence of lock damage is measured through manual operation and measuring tools:
1. Manual movement detection: Push and pull the shaft extension of the output shaft radially, and you can feel obvious radial movement. Normal ZDY315 output shaft radial movement should be ≤0.05mm; when axially levered, the axial movement exceeds 0.1mm, which is far beyond the allowable range of the standard.
2. Turning feel check: When manually turning the output shaft, there is a stuck feeling of tightness and looseness throughout the process, or there is an obvious stuck point at a fixed angle. After turning the stuck point, it returns to smoothness, indicating that the shaft is deformed or metal debris is stuck in the journal.
3. Fitting clearance measurement: Use a dial indicator stand fixed on the box body, with the top of the dial indicator on the key surface of the output shaft journal and coupling installation position. Turn the shaft for one revolution. If the radial runout exceeds 0.03mm, it indicates that the shaft has been bent and deformed; use a feeler gauge to detect the fitting clearance between the shaft and the inner ring of the bearing. If it exceeds 0.05mm, it is judged that the journal wear is excessive.
3. Final confirmation of disassembly (shutdown and maintenance phase)
After disassembling the output shaft assembly, the final determination is made through appearance and dimensional measurements:
1. Appearance damage inspection: If there are visible cracks on the surface of the output shaft, strain and scratches on the journal, deformation and steps on the keyway side wall, or the spline/flat key tooth thickness at the shaft extension end is worn and thinned by more than 5%, the damage will be directly determined.
2. Wear amount verification: Use a micrometer to measure the actual size of the journal fitting position. Compare it with the standard value in the original factory drawing. If the wear amount exceeds 0.02mm, it will cause the bearing to fail to fit and cause severe vibration, and must be repaired or replaced.
3. Oil auxiliary evidence: Check the reducer lubricating oil. The oil is dark brown and mixed with a large amount of metal abrasive particles. Flake metal debris of the shaft material appears on the filter paper, which can further prove that the output shaft has continued wear.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?