Author: Site Editor Publish Time: 23-10-2026 Origin: Site
Many users understand reducers as 'calculation of power, fixed speed ratio, and selection of machine frame number.' The arrangement of the bearings is often left to the on-site decision of the assembly workshop. As a result, after the equipment had been used for one or two years, the input end bearing frequently heated up and the worm shaft made periodic reducer noises . When it was disassembled, it was discovered that the problem was not in the bearing itself, but in the supporting structure: both ends were locked, the shaft stretched due to heat and had no place to go, and the bearing was crushed and ablated. The bearing arrangement determines how the shaft system is positioned, how the thermal elongation is compensated, and who bears the axial force. It is a design item that should be confirmed at the Selection stage. If there is a problem, if it is changed, the cost will be to return the entire unit to the factory.
Arrangement | Structural features | Applicable occasions |
|---|---|---|
Fixed at both ends | The two points each limit one direction and are locked together in two directions. There is a thermal compensation gap c=0.2~0.4 mm between the end cover and the outer ring. | Shafts with short span and low temperature rise, such as the gear shaft of a small gear reduction motor |
Fixed-swimming | One end is bidirectionally positioned to bear axial force, while the other end is free to expand and contract to compensate for thermal elongation. | Common methods for shafts with medium and long spans and large temperature differences, reducer worm shafts, and fan spindles |
Two-end swimming type | Both ends are not axially positioned, and the shaft position is determined by the meshing pair | When the axial position of the driven shaft of herringbone gear transmission is self-centered by the gear |
The most commonly used type of reducer is the fixed-swimming type, which takes into account positioning accuracy and thermal compensation; short shafts with a span of less than 300 mm can be simplified to a fixed type at both ends, and the elongation is absorbed by leaving a gap.
The fixed end must be able to withstand bidirectional axial force. There are three commonly used types: angular contact ball bearings installed in pairs (face to face or back to back, universal assembly series can directly obtain small clearance or light preload), pairs of tapered roller bearings (supplied according to paired clearance, no need to adjust after installation), deep groove ball bearings or double row angular contact bearings (occasions with small axial force and general positioning requirements). At the same time, attention should be paid to the distribution of the radial load and the axial load of the reducer . The combination of four-point contact ball bearings and cylindrical roller bearings is suitable for input shafts with large axial forces and radial forces borne by adjacent bearings.
Axial clearance is the key point for acceptance of the fixed end. If the worm shaft of the worm gear reducer moves more than 0.1 mm, there will be a high and low meshing impact sound. Usually, the axial clearance is controlled within 0.05 mm: add or remove an adjustment shim of 0.02~0.05 mm between the end cover and the outer ring. After installation, use a dial indicator to measure the shaft end, and correct the large deviation piece by piece. The worm gear side is locked with a retaining ring or a round nut on the shaft shoulder to suppress the movement within 0.05 mm.
The amount of movement of the moving end is calculated based on thermal elongation: ΔL = α × L × ΔT, and the steel linear expansion coefficient α ≈ 11.8×10⁻⁶/℃. For example: the span of the worm shaft is 400 mm, and the bearing temperature difference after operation is calculated as 50°C, ΔL = 11.8 × 10⁻⁶ × 400 × 50 ≈ 0.24 mm - this is the minimum amount of expansion that must be reserved for the free end. If less is left, the shaft will still be bent, and the outer ring of the bearing will squirm in the seat hole and become hot, which becomes the most easily missed item in the investigation of the cause of heat in the reducer .
Mobile terminal implementation | Key points of practice |
|---|---|
NU/N type cylindrical roller bearing (recommended) | The rollers can move freely in the outer ring raceway, and both the inner and outer rings need to be axially fixed. The expansion and contraction occurs inside the raceway. |
Deep groove ball bearing outer ring sliding | The seat hole fit is widened and an axial gap of 0.5~1 mm is left between the outer ring and the end cover. The mating surface is coated with anti-creep retaining glue. |
The clearance group must also be matched: the inner ring of the bearing and the shaft usually use k6 transition fit. Interference heating will eat up part of the original clearance. For conventional reducers, choose group C3; for heavy loads, high temperatures, and large interference in the inner ring, consider group C4. During installation, the bearing can be hot-loaded and heated to 80~100℃. Tempering will damage the hardness if it exceeds 120℃.
Preloading is divided into two categories: positioning preloading (nuts and washers press the inner and outer rings in place) and constant pressure preloading (spring constant force loading). Moderate preloading of angular contact and tapered roller bearings can improve stiffness and rotation accuracy. When the operating clearance is slightly greater than zero, the fatigue life is longest; once the clearance enters a significant negative range, the life is shortened sharply and the temperature rise is intensified. Two high-frequency misunderstandings: First, the moving end is pretended to be dead in the same way as the fixed end, and there is nowhere to release the thermal elongation; second, it is better to preload more than less, as a result, the shell will be hot after half an hour of no-load, and in the end, it can only be reworked to replace the reducer bearing.。
There are three points for assembly acceptance: the measured axial movement of the dial indicator complies with the design value (worm shaft ≤ 0.05 mm), the difference between the bearing position temperature and the baseline is recorded point by point after no-load operation (local review exceeds 15°C), and the operating sound is uniform without periodic impact. The data is retained as a baseline for comparison in the next inspection.
There is no unified answer for bearing layout. The span, temperature rise, axial force, and installation orientation (M1~M6) will all change the conclusion. As a manufacturer of reducers, Hangzhou Weigao Transmission can provide complete machine solutions including support structures according to your working conditions, covering a series of products such as hardened cylindrical gears, worm gears, and cycloidal pinwheels. Free parameter calculations are welcome.
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?