The SWC-Ⅰ type universal coupling is the light cross-shaft universal coupling in WGT's SWC programme, built to JB/T 5531-1991 for drives where two shafts cannot be lined up and the joint has to absorb a real angle while still passing torque smoothly. Three versions share one size ladder: A type telescopic welded, B type fixed-length welded and C type short single-unit. Nominal torque runs from 180 N·m to 22 000 N·m over ten sizes, SWC-Ⅰ 58 through SWC-Ⅰ 225, and the maximum working axis angle reaches 35° on the small and medium sizes — far beyond what a flange coupling can tolerate. Against the small fixed-pin universal joints of the CSKA and WS series, the SWC-Ⅰ is a heavy cross-shaft construction with far more torque per joint and much better shock tolerance, while its light build keeps rotating inertia low for a machine that starts and stops all day.
| Model | Nominal torque Tn (N·m) | Fatigue torque Tf (N·m) | Max axis angle β (°) | Rotation diameter Df (mm) | D1 (mm) | D2 (mm, H9) | A-type length L (mm) | A-type mass (kg) | Flange bolts | Bolt torque TK (N·m) |
|---|---|---|---|---|---|---|---|---|---|---|
| SWC-Ⅰ 58 | 180 | 90 | 35 | 58 | 47 | 30 | 255 | 2.2 | M5 | 7 |
| SWC-Ⅰ 65 | 240 | 120 | 35 | 65 | 52 | 35 | 285 | 3 | M6 | 13 |
| SWC-Ⅰ 75 | 500 | 250 | 35 | 75 | 62 | 42 | 335 | 5 | M6 | 13 |
| SWC-Ⅰ 90 | 800 | 400 | 35 | 90 | 74.5 | 47 | 385 | 6.6 | M8 | 32 |
| SWC-Ⅰ 100 | 1200 | 600 | 35 | 100 | 84 | 57 | 445 | 9.5 | M8 | 32 |
| SWC-Ⅰ 120 | 2300 | 1150 | 35 | 120 | 101.5 | 75 | 500 | 17 | M10 | 64 |
| SWC-Ⅰ 150 | 4500 | 2250 | 35 | 150 | 130 | 90 | 590 | 32 | M12 | 110 |
| SWC-Ⅰ 180 | 8400 | 4200 | 25 | 180 | 155.5 | 110 | 640 | 40 | M14 | 180 |
| SWC-Ⅰ 200 | 16000 | 8000 | 25 | 200 | 170 | 125 | 775 | 76 | M16 | 270 |
| SWC-Ⅰ 225 | 22000 | 11000 | 25 | 225 | 196 | 140 | 860 | 128 | M16 | 270 |
WGT catalogue values for the SWC-Ⅰ series. Tn is the nominal torque, taken at 50 % of yield torque; Tf is the fatigue torque, the permissible torque under reversing load set by fatigue strength. Df is the rotation diameter and equals the model number; D1 and D2 are the two principal diameters of the type drawing, D2 specified to H9 fit. A-type mass is for the telescopic welded version; the fixed-length B and C types weigh less at every size. WGT publishes 98.7–99.9 % transmission efficiency and 30–40 dB(A) noise for the SWC family. Non-standard lengths, extension strokes and flange sizes are available on request.
| Type | Construction | Standard length across SWC-Ⅰ 58–225 | Where it fits |
|---|---|---|---|
| A type | Telescopic welded | L 255–860 mm, with an extension stroke on every size | Long spans where the frame moves, or where thermal growth must be taken up without moving the machine |
| B type | Fixed-length welded | L 150–600 mm | Rigid, permanently aligned installations with no axial movement |
| C type | Short single-unit | L 128–480 mm | Compact drives where the shafts sit close together and swing is small |
Lengths are the WGT standard lengths; for telescopic versions L is the minimum length in the fully retracted state. Custom lengths and flange patterns are made to order.
A paint and resin mixer has a 15 kW motor at 750 r/min, the mixer shaft sitting 6° out of line with the motor. The impeller starts against a heavy viscous load several times a shift, so this is a reversing, high-inertia duty.
1. Theoretical torque. T = 9550 × P / n = 9550 × 15 / 750 = 191 N·m. The mixer falls in the heavy-shock group, so a service factor of K = 2.5 applies — the WGT table gives 2–3 for mixers. Calculated torque is Tc = 2.5 × 191 = 477.5 N·m.
2. Use fatigue torque, not nominal torque. Because the load reverses, compare 477.5 N·m against the fatigue torque column. SWC-Ⅰ 90 gives Tf = 400 N·m and is rejected; SWC-Ⅰ 100 gives Tf = 600 N·m and is accepted with a 1.26× margin, against a nominal torque of 1200 N·m. If start-up proves harsher, take K = 3.0 and the next size up.
3. Check the angle. The maximum axis angle of SWC-Ⅰ 100 is 35°, so the 6° offset is comfortable. Remember the SWC rule for equal angular velocity: the two joints must sit at equal angles β1 = β2, the fork ends of the intermediate shaft must be in the same phase, and the three shaft centrelines must lie in one plane. Installations are classified as Z type (parallel axes) or W type (intersecting axes).
4. Choose the construction and set the length. The mixer base settles slightly, so the A type telescopic welded version is used: L = 445 mm, mass 9.5 kg. Flange bolts are M8 and must be tightened to 32 N·m — a loose flange is the most common cause of vibration in a cardan drive.
5. Carry the same factors upstream. That 2.5 service factor belongs on the reducer as well: a service factor gearbox sized with a lower factor will stall on start-up even when the coupling is correct. Feed 477.5 N·m and 750 r/min into your gear reducer selection and gearbox sizing work, then confirm bearing life and thermal rating at the mixer shaft.
Upkeep follows the same discipline. A cardan joint is a maintenance item, not fit-and-forget: put cross-shaft bearing lubrication, flange bolt re-torque and a fork play check into the gearbox maintenance plan, on the reducer oil change schedule.
Open the WGT Motor & Gearbox Online Selection System, enter your power, input speed and required torque, and the system returns matching models with technical data in seconds. Need a cross-reference against an imported SWC, WSS or Japanese cardan shaft? Send the type designation and our engineers will reply with the equivalent, price and lead time within 24 hours.