Author: Site Editor Publish Time: 10-10-2026 Origin: Site
1. Mainstream repair solutions adapted to this model
1. Laser cladding local strengthening repair
This is the preferred solution under 30KW heavy-load conditions: Alloy powder that matches the gear base material is fed into the laser beam simultaneously to form a high-hardness cladding layer of 0.2~0.5mm on the burnt and peeled tooth surface. The heat-affected zone is only 0.1~0.3mm, which will not damage the internal metallographic structure of the gear. The bonding strength can reach more than 90% of the base material. After repair, the tooth surface hardness can be restored to HRC55~60, which is suitable for the heavy-duty transmission requirements of this model.
2. Partial surfacing + precision grinding repair
For moderate burns caused by partial spalling, Cr-Mo wear-resistant electrodes were selected. The gears were preheated to 200°C before welding, and the tooth surface defects were repaired by layered surfacing. Stress relief annealing was performed immediately after welding, and then the tooth shape was ground by a form grinder according to the original module and pressure angle parameters to ensure that the tooth pitch deviation was controlled within the level 7 accuracy of GB/T 10095.
3. Brush plating + tooth surface modification and repair
If the burn only causes the hardness of the shallow layer of the tooth surface to decrease and the wear amount is in the range of 0.1~0.5mm, the surface softening layer can be removed by grinding first, and the tooth surface size can be restored by depositing a nickel-based alloy coating through brush plating. The hardness of the coating can reach above HRC45, and then manually modified with a whetstone, and the meshing contact spots can be checked with red red powder to ensure that the contact area is not less than 60% of the tooth surface.
2. Assessment must be done before repair and the boundary of irreparable
First, use magnetic particle/ultrasonic non-destructive testing to check whether deep cracks extend on the tooth surface. Use a hardness tester to confirm whether the hardened layer on the tooth surface is completely burned. At the same time, measure the tooth thickness reduction to not exceed 10% of the original tooth thickness.
If any of the following conditions occurs, forced repair is not recommended and the meshing gears need to be replaced in pairs: burnt cracks on the tooth surface extend to the tooth root, more than 30% of the tooth surface peeling area, serious tooth shape deformation leading to complete misalignment of the transmission backlash.
3. Post-repair verification and recurrence prevention requirements
Completely drain the old oil, clean all oil circuits, and add TY series standard L-CKD 220# extreme pressure industrial gear oil to the 2/3 position of the oil window.
Gradually load the test run at 50% → 75% → 100% rated load, and monitor the bearing temperature rise throughout the process to not exceed the ambient temperature + 40°C, and the vibration value of the whole machine is ≤ 4.5mm/s.
New oil must be replaced after the first 50 hours of operation, and any metal debris remaining in the repair must be completely removed to avoid secondary scratches on the tooth surface.
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?
Fertilizer Plant Gearbox: Turnaround Season Demand and Sizing Guide
How to judge whether the WP series worm gear reducer is installed in place
How to clean the lubrication system of QJR-D450-20-IX gear reducer
What is the function of the breathable cap of the ZD80-5-2 soft tooth surface gear reducer?
Tissue Machine Yankee Drive Gearbox: Sizing High-Inertia Paper Drives
Wastewater Treatment Gearbox Market 2027: Policy Deadlines and Screw Pump Sizing
Vertical Turbine Pump Gear Drive Selection: Thrust Load, Support and Bearing Life
Gearbox Housing Casting Lead Time: Pour Weight, Pattern Slots, 2027 Windows