WeiGao Transmission
Email: sales@wgt.net.cn
Language
通栏图2
tonglantu.jpg
Home / News / The structure and working principle of the cycloidal pinwheel reducer: small tooth difference meshing, speed ratio gears and maintenance points - Hangzhou Weigao Transmission

The structure and working principle of the cycloidal pinwheel reducer: small tooth difference meshing, speed ratio gears and maintenance points - Hangzhou Weigao Transmission

Author: Site Editor     Publish Time: 19-10-2026      Origin: Site

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

The structure and working principle of the cycloidal pinwheel reducer: How to achieve a large speed ratio from the perspective of small tooth difference meshing

The cycloidal pinwheel reducer is a transmission device based on the KHV small tooth difference planetary transmission principle. It relies on the internal meshing of the cycloidal wheel and the pin teeth to achieve speed reduction and torque increase. Compared with the involute gear reducer, it has smaller volume, larger speed ratio and stronger impact resistance under the same power. Therefore, it is widely used in transportation, mixing, lifting, metallurgy, chemical industry and other working conditions. This article starts from the structural composition and working principle, and explains its speed ratio law, reducer transmission efficiency level and daily maintenance points to help equipment engineers make reasonable judgments when Selection.

1. Five core components: input part, deceleration part and output part

The entire transmission device can be divided into three parts: input, reduction and output. The core components include:

part

Typical materials and processes

Functional role

Input shaft and double eccentric sleeve

Alloy steel is quenched and tempered, and the eccentricity is misaligned by 180° in pairs.

Convert the motor speed into the revolution motion of the cycloidal wheel

Swing arm bearing (eccentric bearing)

Roller bearing

Supports the cycloidal wheel and bears eccentric load

cycloidal wheel

Bearing steel is quenched to HRC58~62 and then finely ground

Core reduction element engaged with pin teeth, used in pairs

Needle housing, needle pin and needle sleeve

Rotatable pin tooth sleeve set on pin

The fixed ring gear forms internal meshing with the cycloidal wheel with a small tooth difference.

W output mechanism (pin type)

Fitting of pin shaft and pin bushing hole

Transmit the low-speed rotation of the cycloidal wheel to the output shaft

Among them, the cooperation between the pin tooth pin and the pin tooth sleeve of the cycloidal pinwheel reducer is the key: the pin tooth sleeve rotates on the pin and rolls in contact with the cycloid gear tooth profile to form a rolling friction pair. The meshing surface basically has no relative sliding. This is the fundamental reason for the small wear and long life of this model. The two cycloidal wheels are 180° offset and mounted on double eccentric sleeves. The inertia forces balance each other, so the operation is smooth and the vibration and noise are low.

2. Working principle: When the input shaft rotates once, the cycloidal wheel only rotates through one tooth in the opposite direction.

When the input shaft drives the eccentric sleeve to rotate for one revolution, the cycloidal wheel is constrained by the pin teeth to perform a planar motion of both revolution and rotation - the input shaft rotates forward for one revolution, and the cycloidal wheel rotates one tooth in the opposite direction relative to the pin tooth housing . In other words, the speed ratio is equal to the number of teeth of the cycloidal wheel: if the cycloidal wheel has 43 teeth, the single-stage speed ratio is 43. This is the most intuitive calculation of the speed ratio of the reducer on the cycloid model: i = z cycloidal wheel , the steering is opposite to the input shaft. The low-speed rotation motion is then transmitted to the output shaft through the pin of the W output mechanism, completing the entire deceleration process.

3. Speed ​​ratio gears and efficiency: single stage 9~87, two stages 121~5133

Designed according to the JB/T 2982 series, the commonly used single-stage speed ratios are 9, 11, 13, 17, 23, 29, 35, 43, 59, 71, and 87; the two-stage series connection can reach 121~5133, and the multi-stage combination can reach tens of thousands. One-stage large speed ratio can replace the complex transmission chain of multi-stage cylindrical gears. Since the meshing is rolling friction and there are many teeth in contact at the same time (up to more than one-third of the number of teeth), the single-stage transmission efficiency is generally 90% to 94%, and the two-stage transmission efficiency is about 88%, which is significantly higher than the worm gear transmission in the same speed ratio range. The transmission torque covers 150~20000 N·m, and the equipped motor power is about 0.25~55 kW.

4. Cycloid wheel wear and daily maintenance points

Although the wear is small, cycloidal wheel wear is still one of the most important failure modes of this model, mostly caused by long-term overload, oil deterioration or pin tooth sleeve jamming. For on-site judgment and processing, please refer to:

  • Temperature rise and abnormal noise: If the oil pool temperature rises above 60°C, the oil temperature exceeds 80°C, or periodic impact sounds occur, the machine should be stopped to check the meshing pair;

  • The hysteresis becomes larger: the idle angle of the output shaft increases significantly, which usually means that the cycloidal wheel tooth profile or pin hole is worn, and the cycloid wheel needs to be replaced in pairs and the pin tooth sleeve is combined;

  • Main points of reducer maintenance : Change the oil regularly according to the instructions (the first oil change is about 300 to 600 hours, and every 2000 to 4000 hours thereafter), check whether the needle sleeve can rotate flexibly, and whether the output end oil seal is leaking;

  • Spare parts principle: cycloidal wheel, pin tooth sleeve, and eccentric sleeve are components. When replacing, it is recommended to replace the complete set and check the model code to avoid mixing.

5. Application Scenarios and Selection Precautions

This model is suitable for continuous operation and allows forward and reverse rotation. Typical applications include belt conveyor, screw conveyor, stirring and mixing equipment, lifting, sewage treatment aerator, etc. Selection In addition to the speed ratio and motor power, the following should also be checked: the working condition coefficient (determined based on load properties, frequency of start and stop, and daily operating hours), cantilever radial load of the output shaft, oil seal and lubrication method during vertical installation, and the impact of ambient temperature on the oil viscosity grade. For the specific relationship between the speed ratio gear and the frame number, please refer to the cycloidal pinwheel reducer model comparison table, and then do a torque check based on the actual load.

If you need to match a suitable model for specific equipment, please contact Hangzhou Weigao Transmission . As a reducer manufacturer, we provide a full range of reducers and geared motors such as cycloidal pinwheels, hard tooth surfaces, worm gears, etc., with free reducer consultation services. We can provide speed ratio, torque and working condition coefficient calibration plans according to working conditions; the local inventory and technical service team of the Hangzhou reducer manufacturer can assist with the entire process from installation to commissioning.

Latest News

WeiGao Transmission

Weigao Gear Reducer is an alliance group company that integrates research and development, production, sales, and service

+86 400 801 9158

Email: sales@wgt.net.cn;wgt.net.cn@gmail.com
Tel:+86571 85023000

WEIGAO REDUCER

FEEDBACK