Author: Site Editor Publish Time: 18-10-2026 Origin: Site
After the equipment is shut down, the maintenance person in charge often has to answer a question: Should this reducer be repaired or should the whole machine be replaced? The basis is not 'is it seriously damaged or not', but three points - whether the damage can be restored to the design accuracy, whether the remaining life after repair is sufficient, and whether the repair cost plus downtime loss is lower than replacement. The following is divided into three parts: gear, journal, and box bearing hole, which can be repaired and must be replaced.
The starting point for reducer repair is measurement, not disassembly. Once the dimensions of the journal, bearing hole, and tooth surface are measured, the process is basically determined. Take journal wear as an example:
Unilateral wear amount | Applicable process | Repair layer hardness | cycle | life expectancy |
|---|---|---|---|---|
≤0.2mm | Brush Plating (Quick Nickel) | HRC50~55 | 1~3 days | 1~2 years |
0.3~1mm | Laser cladding (Ni60A+WC) | HRC60~65 | 3~7 days | 3~5 years |
1~3mm | Machining after thermal spraying or hardfacing | Depends on material | 1~2 weeks | 3~5 years |
>3mm | Insert or change shaft | — | more than 2 weeks | nearly new |
Non-detachable shaft for emergency repair | Polymer composite materials | Shaw D90 | 8~24 hours | emergency use |
Two reminders: the deposition rate of brush plating is about 0.01~0.1mm/h, the coating is thin, the bonding force is limited, and it is easy to peel under heavy load impact; the heat-affected zone of surfacing welding is large, and precision shafts should not be used. In addition, the procurement cycle of reducer accessories is often longer than the repair period.
Among tooth surface damages, reducer gear pitting is easily misjudged. Early pitting corrosion is normal running-in and does not need to be dismantled; if it exceeds the following range, it needs to be dealt with: the average diameter of pits below module 6 is not larger than 1mm, and above module 6 is not larger than 2mm; the pitting area does not exceed 1/5 of the tooth height and tooth length of the effective contact area; the amount of tooth surface wear does not exceed 1/10 of the carburized layer depth; the slight gluing area does not exceed 1/4 of the tooth height and tooth width; the tooth length of the contact spot is not less than 60%, and the tooth height is not less than 45%.
There are three types of treatments for tooth surfaces that exceed the threshold: redistributing the margin and then fine-grinding, which can save most rusted and shallowly worn parts; single-tooth fractures can be treated with the insert method, where the broken tooth root is milled and embedded with an alloy block.
The wear of the journal and keyway is a surface damage, and you can select the process according to the table above; the reasons for the broken shaft of the reducer are mostly fatigue overload, material defects or poor alignment. Once transverse cracks appear, welding can only be regarded as a temporary measure, and the shaft should be replaced and the cantilever load should be reviewed. When replacing the reducer bearing , if the journal has grooves or ovals, the journal should be repaired first and then press-fitted, otherwise the new bearing will also run in circles.
The misalignment of the input shaft coupling will bring additional radial force, which in the long run will cause the bearing outer ring and the box hole to rotate relative to each other, forming a "running circle". For small tolerances, the brush is plated to the size of the drawing and then polished by hand; for large tolerances, the surface is divided and then boxed and bored, or the boring hole is inlaid with a steel sleeve. The interference is 0.02~0.05mm. The joint surface is added with a seam pin to prevent rotation, and the coaxiality is controlled within 0.01mm. Repair welding of cast iron boxes is not recommended as thermal stress can easily cause cracking.
criterion | Tend to repair | Tend to replace |
|---|---|---|
Repair fee accounts for the price of new machine | less than 30% | higher than 60% |
Cabinet status | Bearing hole tolerance is controllable and crack-free | Many places are out of tolerance and cracked. |
remaining life requirements | There is a renovation plan within 3 years | Requires continuous operation for more than 5 years |
Delivery and line suspension losses | Spare parts last for more than 2 weeks, and the loss will be huge if the line is shut down. | New machine will arrive within 4 weeks |
There is another point that is easily overlooked: if the cause of oil leakage in the reducer comes from the deformation of the box or the poor flatness of the joint surface, simply replacing the oil seal will not be effective. This type of box should be replaced instead of repeatedly repairing the seal.
After reinstalling the repair parts, check five items: no-load operation for no less than 2 hours; bearing temperature not higher than 80°C, temperature rise not more than 40K; vibration intensity not higher than 4.5mm/s (2.8mm/s for precision applications); noise not higher than 85dB(A); tooth side clearance and reducer backlash are within the original tolerances when retested. After passing the test, the load is graded from 25% to 100%, each level is stable for 30 minutes, and the current fluctuation and temperature rise are recorded. The maintenance period of the repaired reducer should be shortened by half that of the new reducer. The oil should be changed and tested in the first 500 hours. For cycloid models , the wear of the cycloidal wheel and the clearance of the pin teeth should also be checked.
To sum up: the boundary of reducer maintenance is determined by measurement data - the journal is based on the number of millimeters of wear, the tooth surface is based on the pitting size and the proportion of wear to the depth of the carburized layer, and the box body is based on the bearing hole tolerance and whether there are cracks. All three places can be repaired, and repairing is usually more cost-effective than replacing it with a new one; once there is a crack, a single piece of a pair of gears is damaged, or multiple parts of the box are out of tolerance, it is more economical to replace it with a new one. If you are making a decision about whether to retain old equipment, please contact Hangzhou Weigao Transmission : the company provides a series of products such as cycloidal pinwheel reducers, hardened cylindrical gear reducers, worm gear reducers and gear reduction motors. It can provide free calculations and reducer quotations based on the nameplate and measured data . When replacing imported models, you can also send nameplate photos for model comparison. As a local reducer manufacturer in Hangzhou , we can provide both repair parts and complete machine replacement solutions.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?