Author: Site Editor Publish Time: 11-10-2026 Origin: Site
Oil leakage is one of the more frequent faults during the use phase of A common practice on site is to directly replace the oil seal. It may heal for a while, but then it starts to leak again after a while - the leaking oil may not come from the oil seal, and the leakage point may not be in a visible location. The following is a summary of in the order of 'check the pressure first, then check the oil level, and finally check the seal'.the reducer . six common causes and treatment methods of reducer oil leakage
After the reducer is running, the oil temperature rises and the air expands. When the breathing passage is not smooth, the pressure inside the box is higher than the outside world, and the lubricating oil is pressed toward the oil seal lip and joint surface, and seeps out from the weak seal. The breather cap (respirator) is clogged with sludge and dust or is undersized, which is the real source of many leaks even after replacing the oil seal. Treatment: Remove and check whether the small hole is unobstructed, use fine wire to clear it or blow it clean with compressed air. Use a dustproof ventilation cap with a filter for dusty conditions. For operating in dusty environments such as casting and cement cycloid reducers , it is recommended to clean the vent cap and filter every 3 months.
When the oil level exceeds the upper limit of the oil level, the gear oil churning loss increases, the heat rises together with the pressure in the box, and the splashed lubricating oil accumulates in the shaft hole, exceeding the sealing capacity. If the oil level is too low, the gears and bearings will be insufficiently lubricated, and the local temperature will rise, which will also accelerate the aging of the seals. A safe approach is to control the static oil level near the center line of the oil gauge (or dipstick), generally 1/2 to 2/3 of the visual range, and avoid running with full oil.
The lip of the skeleton oil seal relies on elastic compensation to fit the shaft surface. After the rubber is heated and oxidized for a long time, the elasticity decreases, the lip cracks, and the sealing ability is lost. This is the most common failure mode of When wear grooves appear in the journal or the radial runout is too large (generally required surface roughness Ra≤0.8μm, radial runout≤0.05mm), just replacing the oil seal cannot cure the problem. Treatment: Replace the double-lip skeleton oil seal. For high-temperature conditions, fluororubber (FKM) material can be selected. Before assembly, apply a thin layer of grease on the lip and press it in evenly with a sleeve. If the journal is worn, it can be repaired with chrome plating or a wear-resistant bushing can be installed. If the bearing is loose, replace it in pairs.the reducer oil seal .
The joint surfaces of the upper and lower boxes, end covers and boxes are static seals. Leakage is mostly related to uneven glue application or old glue not being removed, uneven bolt torque, and insufficient flatness of the joint surface. The bolts are not tightened as tight as possible. Uneven torque will deform the joint surface and form gaps. Treatment: Remove the end cover or sight hole cover, remove the old gasket and glue residue, wipe it clean and evenly apply oil-resistant anaerobic flat sealant, and tighten the bolts in diagonal order to the specified torque.
The shaft end of some structures is equipped with an oil return hole or oil return groove, which is used to guide the lubricating oil that has penetrated in front of the oil seal back to the oil pool. This type of pore is often very thin (commonly Φ5~8mm). Once blocked by sludge, more oil will accumulate at the oil seal and leak out under pressure. The oil return of vertically installed hard-tooth surface reducers is more dependent on gravity and the direction of the oil return groove, and the probability of occurrence is correspondingly higher. Treatment: Easily clear the oil during disassembly and inspection; if conditions permit, an oil return groove inclined toward the inside of the machine can be provided at the lower part of the bearing seat, and a gap facing the oil return groove can be opened at the straight opening of the end cover.
A considerable part of the secondary oil leakage comes from the maintenance itself: oil sealing is reversed, press installation is deflected, glue is unevenly applied, and iron filings remain on the joint surface. In addition, oil with too low viscosity and strong permeability, long-term overloading that causes the oil temperature to exceed 90°C to accelerate seal aging, and impact pressure caused by frequent forward and reverse rotations will all induce leakage. Treatment: Check the direction and specifications of the oil seal before assembly, and press it vertically with special tooling; select gear oil with the correct viscosity grade according to the manual; establish a maintenance file to record each leakage point and replacement part model.
order | Check parts | Typical judgment basis | Treatment measures |
|---|---|---|---|
1 | Ventilation cap (respirator) | Small holes are blocked and oil sludge accumulates on the inner wall | Dredge or replace, add a dust cover for dusty conditions |
2 | oil level | Oil level is higher than the upper limit of the oil level | Drain oil to 1/2~2/3 of the center line |
3 | Oil return hole/oil return groove | The tunnel is blocked by oil sludge | Dredge, add inclined oil return hole if necessary |
4 | Box joint surface | Aging of adhesive layer and loose bolts | Re-coat clear glue and tighten diagonally in stages |
5 | Shaft end oil seal/bearing | Cracked lips and shaking output shaft | Replace double-lip oil seals and replace bearings in pairs |
6 | Oil products and working conditions | Oil temperature is too high and viscosity is inconsistent | Change oil according to manual, control load and start and stop |
Hangzhou Weigao Transmission Machinery Co., Ltd. produces a series of transmission products such as cycloidal pinwheel reducers, 、hard tooth surface reducers, 、gear reduction motors, 、worm gear reducers, etc., covering a variety of installation forms and working conditions. If you are dealing with old equipment that leaks repeatedly, or need to make a reducer for a new project , you are welcome to provide the motor power, input speed, output torque, installation method and daily running time. We can calculate the plan for you free of charge and provide a quotation, and also provide matching suggestions for seals and commonly used spare parts. Welcome to send pictures and letters for consultation.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?