Author: Site Editor Publish Time: 16-10-2026 Origin: Site
A shaft mounted reducer hangs directly on the driven shaft of a gearbox for belt conveyor service — no coupling, no baseplate, no laser alignment rig. That simplicity is exactly why installation mistakes are so common: with no foundation to hide behind, the torque arm, the taper bushing kit and the V-belt drive carry every reaction force. Get these three details right and the unit runs for years; get them wrong and you will see bushing spin, bearing failure or a walked-off conveyor shaft within weeks.
The output is a hollow bore that slides over the conveyor head shaft, clamped by twin tapered bushings that grip the shaft evenly around its circumference. Slide the reducer onto the extended head shaft as close to the head shaft bearing as practical — most conveyor manuals specify leaving 38–62 mm (1.50"–2.44") of clearance behind the gearbox for tightening the bushing screws. Positioning the unit too far from the bearing multiplies the bending moment on the shaft and overloads the output bearings.
Tighten the bushing screws to the manufacturer's torque value in sequence, alternating diagonally so the taper draws in evenly. A quality taper bushing tolerates roughly ±1° of angular error at installation, but do not rely on it: verify shaft condition first, because a scored or under-size shaft is the classic cause of bushing spin and gear reducer leak repair calls. Also remember that most units ship without oil — fill to the correct level plug for your mounting orientation before the first start, using the AGMA viscosity grade that matches your ambient temperature range.
The torque arm takes the full reaction torque; the casing would simply rotate on the shaft without it. Three rules from classic shaft mounted reducer practice:
First, anchor the arm to a rigid support on the trough or structure directly behind the head, and arrange the drive so the belt pull acts at approximately 90° to the centre line between the driven shaft and the input shaft — this keeps the arm in tension rather than compression. Second, set the arm roughly at right angles to the centre line through the driven shaft; use the turnbuckle set near full extension to leave maximum adjustment range for belt tensioning later. Third, always lock the turnbuckle jam nut after final adjustment — vibration will walk an unlocked turnbuckle loose and let the gearbox rotate.
Mount the input sheave as close to the reducer input shaft shoulder as possible. Overhung load rises quickly with sheave position: as a rule of thumb, effective overhung load equals belt pull times a drive factor — about 1.5 for V-belts, 1.3 for timing belts and 1.0 for chain — and V-belt drives therefore create the highest input bearing loads. Compare the result against the catalogue overhung load rating and step up the sheave diameter if you exceed it.
For gearbox coupling alignment quality on the belt drive itself, lay a straight edge across the sheave faces and correct both angular and axial error to within about 0.1" per 10" of span. Then tension with the force-deflection method, not by feel: deflect the mid-span by 1/64 inch per inch of span (16 mm per metre) and compare the measured force with the belt manufacturer's table — a higher force for a new belt set, a lower one after the drive has settled in. The neat thing about a shaft mount is that the torque arm turnbuckle is your tensioning device: rotating it swings the reducer about its output hub and changes the belt centre distance directly.
On any inclined conveyor, specify a factory-fitted backstop to prevent reverse rotation under a power loss. Note that many manufacturers restrict lubricant choice with a backstop — avoid unapproved EP mineral oils and follow the lubricant chart supplied with the unit. Standard shaft mounted reducer ratios run from 5:1 up to about 31:1 in single-stage hangere units, with two-stage versions extending far higher; torques range from under 200 N·m on the smallest sizes to 17,000 N·m on the largest, so match the catalogue size to your service factor rather than to motor kW alone.
Before start-up, confirm: bushing screws at final torque, torque arm jam nut locked, belts tensioned by gauge, guard clear of both shafts, oil at the correct level plug, and rotation direction correct against the backstop. A five-minute check list here replaces the most common warranty claims in this product class.
WGT Gearbox (Hangzhou Weigao Transmission) supplies a full shaft mounted reducer range — helical and helical-bevel hang-on units from ATA30 to ATA125 with taper bushing kits, torque arms, backstops and matched conveyor gear motor packages — alongside worm, helical-bevel and planetary series for every duty. We also build SEW- and NORD-compatible drop-in gear reducer replacement units: send a nameplate photo or shaft drawing and we will cross-reference a bolt-in equivalent free of charge. As a China gearbox manufacturer exporting worldwide, we return sizing verification, drawings and a firm gearbox quotation within 24 hours. Tell us your head shaft diameter, belt pull and inclination angle and we will size the complete drive package for you.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?