Author: Site Editor Publish Time: 15-10-2026 Origin: Site
A screw conveyor asks more of its drive than almost any other bulk handling machine: constant torque across the whole revolution, an axial thrust reaction pushed straight into the output bearing, and an environment where the conveyed material is exactly the material that destroys gearboxes. Sizing a screw conveyor reducer cannot stop at motor kW — these five checks decide whether the drive survives ten years on site.
Screw speed is set by the material, not the motor. Free-flowing grain runs comfortably at 60–120 rpm; abrasive powders such as cement, fly ash and silica sand are held to 20–60 rpm to limit flight wear, and a flooded feeder under a full silo runs slower still. Ratio follows directly: i = nmotor / nscrew — a 1,450 rpm four-pole motor driving a screw at 38 rpm needs 38:1. Re-check the actual screw speed against the nearest catalogue step, because a few rpm of error changes fill level and throughput. Where the drive end must stay narrow, a shaft mounted reducer with a hollow output bore slides onto the screw shaft, removing the output coupling and pedestal bearing.
Screw conveyor power is one of the more standardised calculations in bulk handling. The CEMA method splits total power into friction — HPf = L × N × Fd × Fb / 1,000,000 — and material, HPm = C × L × W × Ff × Fm × Fp / 1,000,000, where the material factor Fm runs from about 0.5 for light grain to 4.0 for wet sand or clinker. The gearbox torque calculation then converts drive power to output torque with T = 9,550 × PkW / n: a 7.5 kW screw at 55 rpm needs 1,302 N·m, or a 26.4:1 ratio on a 1,450 rpm motor.
Inclination is where most field failures are born. The incline multiplier applies to the material power component only: about 1.15 at 15°, 1.5 at 25°, close to 2.5 at 45°. A conveyor sized flat and later re-deployed at 30° will overheat its oil within hours.
A screw that starts with compacted material in the trough can demand two to three times running torque to break loose, and that start torque lands directly on the first mesh. The service factor gearbox convention exists for exactly this condition: selection torque equals running torque multiplied by the service factor, never running torque alone.
Material / duty | Running factor | Start factor | Recommended service factor |
|---|---|---|---|
Free-flowing grain, pellets | 1.0 | 1.5 | 1.2 |
Dry cement, fly ash | 1.2 | 2.0 | 1.5 |
Wet sand, mineral concentrate | 1.4 | 2.5 | 1.75 |
Slurry with high solids content | 1.5 | 3.0 | 2.0 |
Sticky clay, adhesive paste | 1.8 | 3.5 | 2.5 |
General conveyor tables put screw conveyors on 16–24 hour duty at 2.0–2.5, so a 1,302 N·m running load should be specified against roughly 2,300–2,600 N·m of catalogue rating. A service factor cannot make a blocked conveyor safe, though — overload protection and a check against permitted peak torque remain separate requirements.
The helix pushes material forward and the material pushes back. On an inclined screw that axial reaction is continuous, which is why screw conveyor drives usually carry taper-roller output bearings and why the frame must be selected on a combined radial and axial rating, not torque alone.
Radial loading is the second trap. A 4 m long, 200 mm screw at 40% fill in wet sand contributes well over 600 N of shaft weight at the drive end before friction is counted. When a screw shaft connects to the output through a rigid coupling with no intermediate bearing, all of that weight rests on the gearbox output bearing. Run a cantilever check against the frame limit — around 2,100 N for a mid-size unit at low speed — and add a steady bearing at the far end for long screws. On a shaft mounted reducer the torque arm must take the full reaction torque, or the casing will rotate on the shaft.
Every gram of cement or talc that reaches the bearing chamber shortens gearbox life. The proven arrangement uses four barriers in series at the trough end: a labyrinth formed by a V-ring and flange, a double-lip seal in the flange, a steel dust disc for abrasives, and a double-lip seal at the gear unit output. A grease nipple with a dedicated expulsion port lets fresh grease push old grease and powder out without building the pressure that destroys lip seals — over-greasing is the most common cause of the gear reducer leak repair jobs we see. Specify IP65 minimum and IP66 for outdoor, coastal or pneumatically pressurised conveying, and use a synthetic PAG lubricant where ambient temperature swings from 8 °C overnight to 48 °C.
WGT Gearbox (Hangzhou Weigao Transmission) builds screw conveyor reducer drives across its industrial gearbox range — shaft-mounted helical and helical-bevel units with CEMA flange adapters, torque arms, backstops and taper-roller output bearings, plus worm and parallel-shaft series and matched conveyor gear motor packages. We also supply SEW- and NORD-compatible drop-in gear reducer replacement: send a nameplate photo or shaft drawing for a free cross-reference. As a China gearbox manufacturer exporting worldwide, we return sizing verification, drawings and gearbox quotation within 24 hours, and our online gearbox selection tool gives a first-pass configuration in under a minute. Send your material, capacity, trough length and inclination angle for a firm proposal.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?