WeiGao Transmission
Email: sales@wgt.net.cn
Language
通栏图2
tonglantu.jpg
Home / News / Reducer oil seal replacement steps and precautions: seven-step standardized operations and avoidance of common mistakes - Hangzhou Weigao Transmission

Reducer oil seal replacement steps and precautions: seven-step standardized operations and avoidance of common mistakes - Hangzhou Weigao Transmission

Author: Site Editor     Publish Time: 14-10-2026      Origin: Site

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

Oil leakage at the shaft end is a high-frequency failure of the reducer, and most of them are attributed to the same thing: the oil seal of the reducer is not replaced properly. There is often feedback at the site that 'the oil seal is still leaking after being replaced.' The problem is often not in the new oil seal itself, but in the three aspects of the journal state, lip direction and press installation technique. This article breaks down the replacement of reducer oil seal into seven steps that can be followed, and provides parameter control points for on-site comparison by maintenance personnel.

1. Identify the source of the leak first, and then take action

Check for leaks before taking action. The shaft end skeleton oil seal is only one of the possible sources. The box joint surface, end cover, oil drain plug and vent hole are also high-risk locations. Mistaking joint surface leakage as oil seal failure will not count as a wasted removal, and will also introduce new hidden dangers. This is a common detour in the investigation of the cause of reducer oil leakage .

Leakage site

Typical phenomenon

processing direction

input/output shaft end

Oil seeps out along the axial direction, there is an oil trace line under the shaft, and oil is thrown away from the inside of the guard.

The skeleton oil seal has failed, please replace it according to the process in this article.

Box split surface and end cover joint surface

Oil seeps out in the form of beads of sweat along the joint seam, and it still seeps out after standing.

The sealing gasket or flat glue fails, re-glue and tighten it.

Vent/breathable cap

The oil level is normal but leakage continues, which worsens after running for a period of time.

The vent hole is blocked, causing internal pressure to rise. Clean or replace the vent cap.

Oil drain plug, oil gauge seat

Oil drips from the thread root and reappears soon after wiping

The combined gasket is aging, replace the gasket and tighten it according to the torque.

Judging based on the oil level and oil quality: the oil level is normal but the leakage continues and worsens after operation. It is most likely that the vent hole is blocked, which increases the pressure in the box. Squeeze the oil out of the lip and clean the breathable cap. The emulsified and white oil indicates that moisture has entered the box, which is mostly caused by seal failure.

2. Preparation before replacement

Safety first: power off and tag out, cool to normal temperature, drain out the old oil, use a puller to remove the coupling or pulley at the axle end, and expose the old oil seal. Prepare an oil seal puller, a press-fit sleeve that matches the outer diameter of the oil seal, a torque wrench, a copper rod or nylon hammer, a lint-free cloth and a feeler gauge, as well as the same type of lubricant, isopropyl alcohol, flat sealant and a small amount of grease. The specifications of the new oil seal must be consistent with the original ones, and the size, number of lips, and materials cannot be mixed.

3. Seven-step process for replacing oil seal of reducer

After confirming that the source of leakage is the shaft end oil seal, follow the following seven steps. Each step has indispensable check points.

Step 1: Disassemble the old oil seal: use a puller to hook the outer ring evenly and pull it out smoothly; if there is no special tool, you can use a flat screwdriver to gently pry it symmetrically around the circumference with a copper sheet. It is strictly forbidden to knock the journal. After taking it out, observe whether the lip is cracked and whether the spring clamp falls off, and based on this, the cause of the failure can be deduced.

Step 2: Check and repair the journal. This step determines the life of the new oil seal: if the scratch depth does not exceed 0.1mm, polish it in the circumferential direction with 600-800 mesh fine sandpaper; if obvious grooves have been formed, a thin-walled stainless steel bushing must be installed to change the contact position instead of hard pressing a new oil seal. The roughness of the contact area should be controlled at Ra 0.2~0.6μm. If it is too rough, it will cut the lip like a file, and if it is too light, the oil film will not be retained.

Step 3: Clean the sealing groove and joint surface: wipe away the residual oil, iron filings and old glue, and use a feeler gauge to check the fit of the end cover. If the gap exceeds 0.05mm, it should be reground or glued. Impurities embedded under the lips are a common cause of leakage after replacement.

Step 4: Choose the right specifications and materials: Nitrile rubber (NBR) oil seals are often used under normal temperature and light load conditions; fluorine rubber (FKM) should be used when high temperatures, heavy loads, or where the oil contains extreme pressure additives. In dusty environments, it is recommended to use a double-lip structure with dust-proof lips, and a small amount of grease can be filled between the two lips.

Step 5: Standardize installation: Apply a thin layer of compatible grease on the surface of the main lip and journal to reduce installation resistance; a thin layer of special sealant can be applied on the metal outer ring, but the lip and shaft surface are strictly prohibited from being glued. The lips must face inward , that is, the main lip with spring faces the oil chamber, and the dust-proof lip faces outward. Otherwise, it will fail. When pressing, use a matching sleeve to apply force evenly until the end face is flush with the notch, and the deflection is controlled within 0.1mm.

Step 6: Reset and tighten: The drive shaft must be strictly aligned when reinstalling, which is also the basic requirement for the alignment of the reducer coupling ; tighten the bolts in two or three times in a diagonal cross sequence to avoid new leakage points caused by flange deformation.

Step 7: Test run verification: Add the specified brand of lubricating oil to the center line of the oil mark, and manually turn the car to confirm that there is no sticking; first run without load for 30 minutes, and check the seal every 10 minutes; then load to 80% of the rated load and run continuously for 1 hour; confirm that there is no leakage and the temperature rise is normal before delivery for production.

4. Key parameter control table

The parameters that need to be quantified and controlled during the replacement of the reducer oil seal are as follows, which can be used as the basis for on-site self-inspection.

Control items

Reference value

illustrate

Journal contact area roughness

Ra 0.2 ~ 0.6 μm

Too much wear on the lip, too much light affects the maintenance of the oil film

Interference between oil seal and shaft diameter

0.1~0.3mm

If the size is too small, the sealing will be insufficient. If the size is too large, it will be difficult to install and the lip will turn over.

Press-fit end face deflection

≤ 0.1mm

Deviation is a common cause of early leakage

The upper limit of repairability of journal scratches

≤ 0.1mm

If the limit is exceeded, the shaft should be inserted or the shaft should be replaced.

End cover bolt torque (M8/M10/M12)

20~25 / 45~50 / 75~80 N·m

Tighten in 2 to 3 steps in diagonal order.

Joint surface fit gap

≤ 0.05mm

If it exceeds the tolerance, it needs to be re-ground or re-glued.

5. Five common mistakes and how to avoid them

Mistakes related to the oil seal during reducer maintenance are concentrated in five places: only the oil seal is replaced without checking the journal, and the new lip falls on the old wear mark; the oil seal is directly hit with a hammer, the outer ring is deformed, and the spring falls off; the lip is installed backwards or the dust lip is installed inside; it is not cleaned before assembly, and iron filings are embedded in the lip; the vent hole is blocked for a long time, and the pressure in the box remains high. The first four items can be avoided by standard work, and the fifth item must be included in the daily reducer maintenance list - it is recommended to check the sealing status every 1000 to 1500 hours of operation, and shorten it to 500 hours in dusty or humid working conditions; the journals exposed when the reducer bearings are replaced should also be inspected to avoid repeated disassembly and assembly.

6. What should I do if it still leaks after replacement?

If there is still leakage after replacement according to the specifications, first distinguish three situations: the assembly is skewed or the lip is scratched, which shows that new oil stains are visible in a short period of time, and the lip needs to be dismantled and reinstalled and the lip needs to be inspected; the journal groove is too deep and has only been polished, so a repair solution with a bushing should be used; the leakage actually comes from the joint surface or the vent hole, but the location is close and is misjudged. Eliminating each issue one by one before proceeding will save costs and downtime rather than repeatedly replacing oil seals.

Conclusion: Turn "replacement" into "restoring sealing ability"

Back to the initial question - why does the replacement of the reducer oil seal often result in a new oil leak? Because it is not just a replacement of a rubber ring, but a sealing system composed of journal accuracy, lip direction, press-fitting technique and box ventilation status. Only when the journal is repaired in place, the material and number of lips are selected correctly, and the oil seal can restore its oil-sealing capability by pressing it according to the parameters and tightening it diagonally. The shaft end sealing principles of cycloidal pinwheel reducers, hard tooth surface reducers and various gear reduction motors are similar. By mastering this process, most leaks can be solved in the factory.

If you need to check the oil seal specifications or arrange replacement, please consult Hangzhou Weigao Transmission

Hangzhou Weigao Transmission Machinery Co., Ltd. is a reducer manufacturer specializing in transmission equipment . Its product line covers cycloidal pinwheel reducers, hard tooth surface reducers, coaxial reducers, worm gear reducers and gear reduction motors. It can provide oil seal specification verification, spare parts matching and model comparison for old machine replacement for transportation, lifting, mixing, metallurgy and other working conditions. If you are experiencing oil leakage at the shaft end or need spare parts in batches, send us the photo of the reducer nameplate, installation posture and working environment, and we will provide free reducer consultation and replacement solutions. As based in Hangzhou a Hangzhou reducer manufacturer , we also welcome drawings and samples to customize and negotiate complete machine packages.

Latest News

WeiGao Transmission

Weigao Gear Reducer is an alliance group company that integrates research and development, production, sales, and service

+86 400 801 9158

Email: sales@wgt.net.cn;wgt.net.cn@gmail.com
Tel:+86571 85023000

WEIGAO REDUCER

FEEDBACK