WeiGao Transmission
Email: sales@wgt.net.cn
Language
通栏图2
tonglantu.jpg
Home / News / Overhung Load Explained: Protecting Your Gearbox Output Shaft

Overhung Load Explained: Protecting Your Gearbox Output Shaft

Author: Site Editor     Publish Time: 14-10-2026      Origin: Site

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

What Is Overhung Load on a Gear Reducer?

Every gear reducer catalog lists torque, ratio and speed — but one number causes more silent field failures than any other: the overhung load gear reducer rating. An overhung load (OHL) is the radial force applied sideways on the output shaft by whatever hangs on it — a chain sprocket, V-belt pulley, timing pulley, pinion or wheel. Unlike torque, which twists the shaft, OHL bends it. If the actual side pull exceeds the permissible value, the output bearings fail prematurely even though the torque rating seemed perfectly adequate. In our service records, a large share of unexplained gearbox bearing failure cases under one year of service trace back to an uncalculated overhung load, not to poor lubrication or assembly quality.

The Overhung Load Formula: How to Calculate It

The standard formula used across manufacturer catalogs (SEW-Eurodrive, Winsmith, Renold and AGMA references) is:

OHL = (2 × T ÷ d₀) × fz

where T is the output torque, d₀ is the pitch diameter of the mounted sprocket, gear or sheave, and fz is the transmission element factor. The factor accounts for extra side pull beyond pure torque transmission — belt pre-tension, gear separating forces and so on:

Transmission element

Factor fz

Chain sprocket (≥ 20 teeth)

1.00

Spur / helical gear (≥ 17 teeth)

1.00–1.25

Timing belt pulley

1.30

V-belt pulley

1.50–1.75

Flat belt pulley

2.50

Variable-speed drive pulley

2.5–3.5

Worked example: a conveyor drive delivers 800 N·m output torque through a 200 mm pitch-diameter chain sprocket. OHL = (2 × 800 ÷ 0.2) × 1.0 = 8,000 N, plus the sprocket's own weight. If the catalog permissible OHL for the selected frame is only 6,500 N at the load point, the bearings are already overloaded — before any shock load is applied.

Three Rules That Extend Output Bearing Life

Rule 1 — Mount the load as close to the housing as possible. OHL capacity is always quoted at a reference point (usually mid-shaft or one shaft diameter from the seal face). Every millimeter outward adds bending moment: manufacturers' conversion tables show capacity dropping to roughly 65% at two shaft diameters, 45% at three, and 30% at five. Doubling the overhung distance can effectively halve the bearing life.

Rule 2 — Use the largest practical sprocket or pulley diameter. OHL is inversely proportional to pitch radius. Going from a 150 mm to a 250 mm sprocket cuts the calculated OHL by 40% at the same torque — often the cheapest fix of all, and a critical point in any gearbox selection guide for chain and belt drives.

Rule 3 — Apply the service factor to the OHL, not just the torque. Shock loads from crushers, punch presses or frequent starts multiply the side pull the same way they multiply torque. A standard service factor gearbox check of 1.25–2.0 must be applied to the calculated OHL before comparing it with the catalog value.

What to Do When the Overhung Load Still Exceeds the Rating

If the calculated OHL exceeds the permissible value, you have four practical options in ascending cost order:

  1. Increase the pitch diameter of the sprocket, pulley or pinion.

  2. Move the mounted element closer to the housing shoulder.

  3. Add an outboard (external) bearing to support the shaft end.

  4. Mount the sprocket on a separately supported shaft coupled to the reducer, or step up to the next frame size.

Remember also that axial thrust and OHL interact: most catalog units accept axial force up to about 50% of the permissible OHL, but combined radial-plus-axial duty should always be verified case by case during gear reducer sizing.

Conclusion: Check the Shaft Before You Check the Price

Torque and ratio decide whether a gear reducer can turn the load; the overhung load decides whether it survives the application. Specify the element type, pitch diameter, load position and direction of pull in every RFQ, and any competent supplier should return a verified OHL check with the offer.

As a China gearbox manufacturer in Hangzhou, WGT Gearbox supplies cycloidal pinwheel reducers, hard tooth surface helical and bevel-helical units, worm gear reducers and gear motors — with full drop-in replacement capability for SEW and NORD series. Send us your application sketch or nameplate photo, and our engineers will return a complete gearbox quotation with an OHL verification and technical drawings within 24 hours.

Latest News

WeiGao Transmission

Weigao Gear Reducer is an alliance group company that integrates research and development, production, sales, and service

+86 400 801 9158

Email: sales@wgt.net.cn;wgt.net.cn@gmail.com
Tel:+86571 85023000

WEIGAO REDUCER

FEEDBACK