WeiGao Transmission
Email: sales@wgt.net.cn
Language
通栏图2
tonglantu.jpg
Home / News / Materials and heat treatment process of reducer gears: carburizing and quenching, gear grinding accuracy and tooth surface hardness - Hangzhou Weigao Transmission

Materials and heat treatment process of reducer gears: carburizing and quenching, gear grinding accuracy and tooth surface hardness - Hangzhou Weigao Transmission

Author: Site Editor     Publish Time: 18-10-2026      Origin: Site

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

Why is the tooth surface hardness determining the bearing capacity of the reducer?

The most essential difference between The industry uses Brinell hardness 350HBS as the dividing line: the tooth surface hardness below 350HBS is called soft tooth surface, and the tooth surface hardness exceeding 350HBS (usually Rockwell hardness HRC58~62) is called hard tooth surface. After the tooth surface hardness is increased, the tooth surface contact fatigue strength increases exponentially, and the load-bearing capacity under the same volume can be increased to 2 to 3 times that of the soft tooth surface model. At the same time, a hard-tooth surface reducer and a soft-tooth surface model of the same specification is hidden in the tooth surface of the gear. the transmission efficiency of the reducer is also more stable (a single stage can reach more than 96%). The performance of this set of 'hard on the outside and tough on the inside' completely relies on the combination of gear materials and heat treatment processes. It is disassembled in four steps below.

How to choose gear materials: 20CrMnTi and 42CrMo, what working conditions do they care about?

Hardened surface gears generally use two categories: low carbon alloy steel and medium carbon alloy steel. Low carbon alloy steel (20CrMnTi, 20CrMo, 18CrNiMo7-6, etc.) has good hardenability. After carburizing and quenching, it can form a combination of high hardness surface layer and high toughness core. It is the mainstream choice for heavy-duty gears; medium carbon alloy steel (42CrMo, 40Cr) is mostly used for quenching and tempering, and is suitable for shaft parts and medium and low load gears. When selecting materials, you should also pay attention to the core hardness: the core of carburized gears is generally controlled at HRC30~40. If the core is too hard, it will easily break, and if it is too soft, plastic deformation will occur under heavy load. This is directly related to the reducer Selection - in working conditions with large impact loads and frequent starts and stops, you should confirm that the manufacturer provides core toughness data, not just tooth surface hardness.

Carburizing and quenching process: How is the tooth surface HRC58-62 obtained?

Carburizing and quenching is the core of the hard tooth surface process. The low carbon alloy steel tooth blank is first rough hobbing, and then in a carburizing furnace at 900 to 950°C, activated carbon atoms are allowed to penetrate into the tooth surface. The depth of the carburized layer is 0.8 to 1.2mm according to the modulus (1.2 to 1.6mm when the modulus is greater than 10). It is then oil-cooled quenched and tempered at a low temperature of 180 to 200°C to eliminate internal stress. The key parameters and common defects are compared as follows:

Process link

control points

Consequences of loss of control

Carburizing temperature and carbon potential

900~950℃, carbon potential 1.1%~1.3%

If the carbon potential is too high, network carbides will be formed, and the tooth surface will easily peel off.

Depth of seepage layer

0.8~1.5mm, graded according to module

Insufficient penetration layer may lead to surface crushing and premature pitting corrosion.

Quenching and cooling

Oil cooling, control deformation

Excessive deformation leads to insufficient gear grinding allowance

Low temperature tempering

180~200℃ stress relief

Residual stress causes grinding cracks

Tooth surface hardness

HRC58~62 (test report comes with the goods)

If it is lower than HRC55, it needs to be repaired or replaced.

Some small and medium-module gears will also use nitriding or induction quenching: the hardness of nitriding treatment can reach HV850~1200, with small deformation, suitable for medium-low speed and heavy load; induction quenching is mostly used for hardening of large-module single teeth. When purchasing, ask for the heat treatment curve chart and hardness test report from the manufacturer, which is the direct basis for judging quality.

Gear grinding accuracy: a key step after heat treatment

Carburizing and quenching will inevitably cause gear deformation, so hard tooth surface gears must undergo CNC gear grinding and finishing after heat treatment. According to the accuracy standard of GB/T 10095 (corresponding to ISO 1328), hard tooth surface gears are usually required to reach level 5 to level 6 accuracy, with tooth surface roughness Ra≤0.8μm, and ring gear radial runout controlled within 0.05mm; in precision transmission applications, it can be increased to level 4 to level 5. The quality of the grinding teeth directly determines the meshing spot distribution and noise level, and also affects the occurrence time of reducer gear pitting corrosion - when the tooth profile error is large, the load is concentrated on the tooth top or tooth root edge, the local contact stress is doubled, and fatigue pitting corrosion will appear early. By comparison: soft tooth surface gears can be precision rolled after heat treatment (about 8 levels of accuracy), the process is simple and low cost; hard tooth surface gears follow the 'carburizing and quenching + gear grinding' route, which has many processes but has overall advantages in accuracy, load-bearing capacity and lifespan. This is also the reason why hard-tooth surface cylindrical gear reducers have become the main model in heavy-duty continuous working conditions such as metallurgy, mining, lifting, cement, etc.

Attention on the user side: pitting corrosion monitoring and maintenance points

No matter how good the craftsmanship is, routine maintenance is needed to ensure its longevity. Hard-tooth surface models have high contact stress, so heavy-duty extreme pressure gear oil (L-CKD grade) should be used. The oil change interval is more frequent than that of soft-tooth surface models (first inspection after 1000 to 1500 hours of operation, and then determined according to the oil condition). Three key points should be paid attention to in the daily maintenance of the reducer : first, regular listening and vibration measurement. The characteristic of tooth surface spalling is the occurrence of meshing frequency sidebands in the frequency spectrum; second, unboxing and checking the pitting and spalling area of ​​the tooth surface every 5,000 hours of operation. Repairs should be arranged when the pitting exceeds the specification limit or the tooth surface hardness drops significantly; third, keep the oil temperature at 40-60°C and the oil level within the calibration range. Lubrication failure is a common cause of early failure of hard-tooth surface gears. By solidifying these inspections into a check list, the gear life can reach the designed tens of thousands of hours.

Hangzhou Weigao Transmission’s hardened gear technology and Selection support

As a reducer manufacturer, Hangzhou Weigao Transmission 's hard-tooth surface reducer product line covers hard-tooth surface cylindrical gear reducers, cycloid pinwheel reducers, worm gear reducers, gear reduction motors and other series. The gears strictly follow the carburizing and quenching and CNC gear grinding process, and a material list and hardness test report are provided with the goods. If you are comparing the plans of Hangzhou reducer manufacturers , or need to calculate the tooth surface contact strength and thermal power according to working conditions, you are welcome to provide the motor power, speed, torque and installation dimensions. We provide free reducer consultation and issue complete plans and technical parameters for your reference.

Latest News

WeiGao Transmission

Weigao Gear Reducer is an alliance group company that integrates research and development, production, sales, and service

+86 400 801 9158

Email: sales@wgt.net.cn;wgt.net.cn@gmail.com
Tel:+86571 85023000

WEIGAO REDUCER

FEEDBACK