Author: Site Editor Publish Time: 04-12-2019 Origin: Site
Generally, cycloid reducers are divided into flange type and special motor direct connection type.The ordinary motor with flange directly separates the motor from the flange connection part, which is more convenient to disassemble.Generally, this is not a problem.Generally, starting from the end of the output shaft, erect the end of the motor on the ground, remove the oil seal, remove the end cover from the base, and then remove the swing plate, eccentric bearing and needle housing.Come out one by one.Usually, disassembly is not a problem, but the installation of the cycloid reducer is very special, especially the ornaments must not be installed incorrectly.
Introduction to the installation method of cycloidal pinwheel reducer
1. When purchasing a cycloidal wheel, please check whether the two cycloidal wheels are in a pair.The manufacture of cycloids is based on a pair (that is, a pair) as a unit.Purchases are also one-to-one or one-to-one purchases.The individual cycloid wheels per payment are not interchangeable, and the two wheels of the cycloid wheel are not separated during the production process.The concept of a pair is that the two cycloidal wheels can be completely overlapped (that is, when the side with the stamp is placed upward at the same time), the bearing hole is enlarged, and the ten holes (shaft pin hole) and the external tooth type are simultaneously fully overlapped.It looks like a piece from the front.If it can be completely overlapped, it is proved to be a pair and cannot be overlapped.Instructions are not a pair and cannot be used.Notice.Anyway, the cycloid wheel is there.There are marks on the cycloidal wheel, and the marked side must face up during installation.Each pair of cycloidal wheels is also marked differently.The location of the number marks keyed in by each manufacturer is different.The marking positions of domestic manufacturers are generally coincident position markings (the marking positions coincide), but there are also installation position markings.Wherever it's marked, it's just an aid to help check that it's a pair of wheels.
2. Rotate one of the cycloid wheels 180 degrees.That is, when the middle bearing hole and the ten holes completely overlap, the outer tooth profiles are just misaligned.The position of the tooth root of the upper part is exactly the position of the tooth crest of the lower part.Notice.The relative position of these two wheels must be remembered.It's better to mark it yourself.Or memorize where the original markings were on the wheel.(This is a cycloidal wheel with a single tooth difference. Two tooth differences do not need to rotate 180 degrees)
3. Put a cycloid needle in the cycloid needle case.Turn it by hand to see if it is smooth.Whether to swing.
4. Insert the eccentric bearing.Because the bearing hole of the cycloid bearing is equivalent to the shell of the eccentric bearing.Therefore, the correct position of the eccentric bearing is that the bearing hole of the cycloid gear completely contains the cylindrical ball of the eccentric bearing.
5. Put in the isolation ring.It's an iron ring smaller than a cycloidal needle (now some of them are not iron)
6. Put in another cycloidal wheel.The most important thing is to put this wheel.The embossed characters of this cycloidal wheel must be upward as the embossed characters of the bottom cycloidal wheel, the embossed characters of the upper and lower cycloidal wheels must be staggered by 180 degrees, and they must be in a straight line.Characters with upper and lower cycloids cannot be placed together!Special attention must be paid to this point!(Note: Individual manufacturers have marked the installation coincidence mark on the cycloidal wheel, but the only exception is that the upper and lower cycloidal wheels of all Changzhou-made cycloidal pin wheel reducers must be staggered by 180 degrees!)
7. Put the bushing into the cycloidal pinhole accordingly, and turn it by hand to see if it can be turned.Check that the installation is correct.If it can rotate smoothly, you can install the basic parts to synthesize a complete cycloid reducer, haha!At this point, you can consider it complete
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?