Author: Site Editor Publish Time: 16-10-2026 Origin: Site
The lifespan of the same industrial gearbox installed on two production lines may be more than doubled. The difference is often not in the product itself, but in the installation and first test run. Insufficient installation accuracy will cause gears to be overloaded and bearings to be fatigued in advance; if abnormalities are not caught during the test run, small problems will quickly magnify into broken teeth and burned bearings after loading. This article explains the judgment method in the order of installation, commissioning and acceptance.
Foundation and embedded parts : The strength of the concrete foundation shall not be less than C25, the surface flatness deviation shall be within 2mm/m, and the anchor bolt position deviation shall not exceed ±5mm;
Model and accompanying documents: Check whether the model, speed ratio, and rated torque on the nameplate are consistent with the design, and archive the installation manual for future reference;
Lubricating oil and oil level : Add the specified grade of gear oil (usually ISO VG220 or VG320) according to the manual. The oil level should be near the center line of the oil mark when shutting down. If it is too high, it will aggravate the oil churning and heat, and if it is too low, the oil film will be insufficient.
Measure the level first. Use a level with an accuracy of 0.02mm/m to measure the longitudinal, transverse and axial end surfaces of the box base, and control the deviation within 0.05mm/m ; the pads should be arranged neatly and closely fit the base, and are not allowed to be suspended.
Then do the shaft system alignment. Use a laser alignment instrument or dial indicator to detect the coaxiality between the input shaft and the motor shaft, the output shaft and the load end. The radial deviation should be controlled within 0.05mm, and the angular deviation should not exceed 0.1° . The coupling must reserve a thermal expansion gap; when using a sprocket or pulley for external transmission, the radial load of the reducer must be calculated . The additional cantilever load caused by excessive tension is a common cause of output shaft breakage.
Tightening is divided into three times according to the torque-angle method: pre-tightening 30% → 70% → 100%. For example, the final tightening torque of grade 8.8 M24 bolts is about 640N·m (subject to the manual). After 24 hours of operation, the anchor bolts must be retightened . This step is often skipped, but it is the direct source of box deformation and gear eccentric load.
Turn the car to confirm that the rotation is flexible and then jog three times to confirm that the steering is consistent with the housing mark (no more than 3 seconds each time), and then enter the no-load test run: start at 25% of the rated speed, increase step by step in 25% increments, each gear is about 30 minutes, and run continuously for no less than 2 hours after reaching the rated speed, and record a set of data every 30 minutes.
Test items | Reference limits | Common reasons for exceeding the standard |
|---|---|---|
Bearing temperature | Not exceeding 80℃, temperature rise not exceeding 40K | Insufficient lubrication and excessive preload |
Oil pool temperature | Within 80℃, no more climbing | Oil level is too high and viscosity does not match |
Vibration intensity | Generally no more than 4.5mm/s, precision models no more than 2.8mm/s | Loose feet and poor alignment |
Noise (from 1 meter) | No more than 85dB(A), uniform sound | Tooth side clearance is too small, bearing damage |
Sealing part | Allows a very slight oil film, no dripping | The oil seal is deflected and the breathable cap is clogged |
If the temperature continues to rise or the reducer makes abnormal noise during the no-load stage , the machine should be shut down immediately for investigation - loading unqualified equipment under no load will only accelerate damage.
Each load can run stably for more than 30 minutes, and full load can run continuously for no less than 2 hours. Focus on three things: whether the temperature gradually stabilizes instead of continuing to climb; whether the vibration increases significantly with the load (sudden changes lead to poor alignment or gear bias); whether the current is stable and the fluctuation should be within ±5%. After stopping the machine, re-measure the tooth side clearance and bearing clearance according to the drawings. If necessary, use the coloring method to confirm the contact spots (not less than 60% in the tooth length direction and not less than 45% in the tooth height direction).
Vibration exceeds the standard: first check whether the pre-tightening force of the anchor bolts is attenuated, and then recheck the alignment accuracy; if the meshing frequency component is prominent, stop the machine and adjust the gear meshing parameters;
Abnormal temperature rise: If the temperature rise exceeds 10℃ within half an hour, stop the machine and check the oil quantity, oil quality and bearing preload;
Leakage: First check the oil level and breather cap, and then confirm whether the oil seal installation direction and lip are damaged.
Fill in the acceptance form item by item for levelness, coaxiality, bolt torque, and temperature, vibration, noise, and current under each load level. If any item is not up to standard, readjust it and re-inspect it. These data are also the baseline for subsequent maintenance: after the first operation of about 500 hours, replace the running-in oil and clean the box. After that, the oil change cycle is determined according to the working conditions. The alignment and side clearance are re-tested every quarter. When there is a deviation trend, maintenance is arranged in advance. Most reasons for the reducer’s heating and early broken teeth can be discovered at this stage.
The judgment standards are slightly different in each manual. For non-standard working conditions or large units, it is recommended to refer to the manufacturer's technical documents. If you are supporting or replacing industrial gearboxes for production lines , please feel free to consult Hangzhou Weigao Transmission: We provide cycloidal pinwheel reducers, hardened cylindrical gear reducers, worm gear reducers, planetary reducers and various gear reduction motors. As a reducer manufacturer with many years of industry experience and a Hangzhou reducer manufacturer , we can provide free Selection calculations, imported brand model comparisons and reducer Selection consultation , and engineers will issue plans and quotations within 24 hours.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?