Author: Site Editor Publish Time: 14-10-2019 Origin: Site
After using the reducer for a long time, a comprehensive inspection should be carried out so that some hidden dangers can be found in time.In order to keep the equipment running efficiently, we usually refuel in time.But we should also solve the oil spill problem in time.
1. Carry out the maintenance process carefully.When overhauling, the process regulations must be carefully implemented.The oil seal must not be installed in reverse, the outer edge must not be deformed, the spring must not fall off, the surface of the joint must be clean, the sealant must be evenly applied, and the amount of oil must not exceed the oil stain.
2. Improve the ventilation hole cover and inspection hole cover.The internal pressure of the reducer is greater than the external atmospheric pressure, which is one of the main reasons for oil leakage.Oil leakage can be prevented if the pressure inside and outside the machine is balanced.The inspection hole cover must be opened every time refueling.Once opened, the possibility of oil leakage will increase once, and the leakage will occur in the original position.Therefore, an oil cup type exhaust cover was made, and the original thin inspection hole cover was changed to a thickness of 6mm, and the oil cup type exhaust cover was welded to the cover.The vents are 6mm in diameter for easy ventilation.The pressure is balanced, refueling from the oil cup when refueling, without opening and checking the hole cover of the reducer, thus reducing the chance of oil leakage.
Three, wipe.Static seals can usually be treated to prevent leakage.However, due to the aging of the seal, poor quality, improper assembly and high surface roughness of the shaft, the leakage of the dynamic sealing point is still small.The working environment is harsh, coal dust sticks to the shaft and looks greasy.Therefore, the oil on the shaft must be wiped off after the equipment stops running.
Fourth, keep it open.In order to prevent the reducer gear from accumulating too much lubricating oil on the shaft seal, it is necessary to flow the excess lubricating oil back to the oil pool in a certain direction.The oil return groove inclined towards the inside of the machine is opened in the center of the lower shell of the bearing housing, and there is also a gap in the straight opening of the end cover.
5. Use new sealing material.For static sealing point leakage, a new type of polymer repair material can be used for sticking and plugging, so as to eliminate oil leakage.
six.Improve the shaft seal structure.
The oil leakage of the reducer is mainly related to some accessories.In particular, check the fuel tank at this time.Note that the oil does not have to be topped off, or the chances of an oil leak may increase.The other is to check the tightness of the device.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?