Author: Site Editor Publish Time: 25-10-2026 Origin: Site
The coupling in the transmission chain is a component with a very low unit price, but it is often left to be filled in according to the shaft diameter before placing an order. If you choose the wrong one, the fault is often not your own: tearing of the elastomer, shearing of the bolts, and additional radial force will transfer the load to the output shaft and bearings of making the reducer . When a reducer , the coupling should be calibrated synchronously with the speed ratio and service coefficient. This article explains the configuration method in three steps according to type, torque, and compensation amount.
type | Compensation ability | Vibration damping | Applicable speed | Typical occasions |
|---|---|---|---|---|
rigid flange | almost none | 无 | Medium and low speed | Good alignment, smooth heavy load |
Plum elastic (ML/XL) | 中 | 好 | Middle to high | Pumps, mixing, general units |
Elastic pin (HL)/elastic sleeve pin (LT) | 中 | 好 | 中 | Fans, conveyors, general drives |
Diaphragm (metal) | The angle is good in the axial direction and the radial direction is small. | 弱 | 高 | High-speed unit, maintenance-free occasion |
Tooth/Drum gear | 大 | 无 | 中 | Low speed and heavy load, metallurgical mining |
tire type | 大 | 好 | medium low | Big impact, poor alignment |
Safety coupling/torque limiter | With the body | With the body | arbitrary | Stalled rotor, jammed material and overload conditions |
Selection principles: Prioritize elasticity or diaphragm for high speed and light load; select gear type for low speed and heavy load; select tires or high elastomer for frequent impact; transport and crushing lines with risk of stalling should be connected with a first-level safety coupling after the elastic coupling.
The coupling at the output end of the reducer transmits output torque, which is one speed ratio magnitude larger than that at the input end. First use T = 9550 × P / n to calculate the nominal torque, and then multiply it by the working condition coefficient K to get the calculated torque Tc = K × T. The nominal torque of the coupling is not lower than Tc. Commonly used values of K:
Load properties | Working condition coefficient K | Typical equipment |
|---|---|---|
smooth | 1.0~1.5 | Fans, centrifugal pumps |
slight impact | 1.5~2.0 | Belt conveyors, machine tools |
medium impact | 2.0~2.8 | Mixers, air compressors |
strong impact | 2.8~4.0 | Crusher, rolling mill, punch press |
Calculation example: 15 kW four-stage motor 1465 r/min, reduction ratio 25, efficiency 0.95, output approximately 58.6 r/min. The nominal torque on the input side is about 98 N·m, which is about 196 N·m when multiplied by K=2.0. A plum blossom coupling is enough; the nominal torque on the output side is 98 × 25 × 0.95 ≈ 2322 N·m, which is about 4645 N·m when multiplied by 2.0. It must be selected according to the sample specifications of elastic pin or tooth type. The specifications of the two are completely different. For units that start and stop frequently or rotate forward and reverse, increase K by one gear and check the peak torque given in the sample.
The allowable speed of the selected specifications must be higher than the working speed and leave a margin; the rubber elastomer coupling will heat up and age quickly when running above 3000 r/min for a long time, and the high-speed diaphragm will be given priority. The shaft hole diameter and keyway are selected in accordance with GB/T 3852. If the shaft diameters at both ends are different, check the wall thickness end by end. Thin-walled hubs that are bored to the upper limit are prone to cracks. The dynamic balance grade of conventional transmission is G6.3. If the speed exceeds 3600 r/min, it is recommended to perform dynamic balance according to G2.5 and check the critical speed.
The radial and angular compensation amounts marked on the sample are the upper limit of the capability , not the construction tolerance. Engineering practice is to control the actual installation deviation within 20% of the allowable compensation amount, leaving the rest for thermal running-in and foundation settlement. During installation, the coupling alignment standards are still followed: the radial deviation of the rigid connection shall not be greater than 0.02 mm, the elastic connection shall not be greater than 0.05 mm, and the angular deviation shall be re-measured at four points on the end face with a dial indicator. The elastomer should be visually inspected every six months. If there are any pieces falling off, hardening, or oil swelling, replace the elastomer in its entirety. Do not assemble and mix them.
The commonly used upper temperature limit of polyurethane elastomer is about 80 ℃. If the ambient or body temperature exceeds, replace the FKM rubber or metal diaphragm; the oil mist and dust environment will accelerate the swelling and wear of the elastomer, so choose a cover structure. For corrosive environments, choose stainless steel diaphragms or coated pins. When the low temperature is lower than -25 ℃, ordinary rubber becomes brittle. Please indicate the working conditions and let the factory prepare low-temperature elastomers.
The first is to only check the shaft diameter without multiplying the working condition coefficient, and the elastomer is torn during the first month's peak load; the second is to use the motor nameplate torque to the output side coupling Selection, and the overall specification is too small; the third is to rely on the elastomer to handle excessive alignment. As a result, the bearing is pitted in advance and the coupling backlash is getting larger and larger, which in turn induces abnormal noise in the reducer.。
The coupling, motor and reducer are a whole. Hangzhou Weigao Transmission provides torque chain calculation and interface size verification at the reducer stage, covering the entire product line of hardened tooth surfaces, cycloid pinwheels and worm gears, and can recommend matching coupling forms according to working conditions. If you have consultation needs from reducer manufacturers Selection, you are welcome to submit power, speed and load parameters to obtain the configuration plan.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?