Author: Site Editor Publish Time: 24-10-2026 Origin: Site
Among the various failure modes of a reducer , the treatment cost and downtime impact of broken teeth are ranked high: pitting corrosion and wear can also be monitored and operated. Once the gear teeth are broken, metal debris will quickly contaminate the entire oil pool, often bringing down the paired gears and bearings within a few hours. Many sites simply attribute broken teeth to 'poor quality' and replace them with the same model and continue to use them. As a result, they break again at the same location a few months later. In fact, broken teeth are only the result, and the fracture and fracture location are the causes. This article starts from the mechanism and explains how to distinguish fatigue fracture and overload fracture from the fracture surface, how to troubleshoot the four root causes, and what specific steps should be taken in Selection and maintenance.
First, let’s give an overall judgment framework: most gear tooth fractures occur at the tooth root , because the bending stress is concentrated here, and there are machining tool marks and material defects at the transition fillet. However, the location of the fracture and the shape of the fracture are different, and the root causes are completely different. After getting the broken tooth, do not clean and assemble it first. Take photos of the fracture first and keep the actual broken tooth. The subsequent judgment will all depend on it.
Every time the gear teeth mesh, the tooth root is subjected to alternating bending stress. When the bending stress of the tooth root approaches the fatigue limit of the material for a long time, cracks will originate from the surface of the tension side of the tooth root and gradually expand along the tooth root fillet or obliquely toward the tooth tip. The macroscopic characteristics are very typical: the fracture surface is divided into two parts: fatigue expansion zone and instantaneous fracture zone - the expansion zone is smooth and shiny, and you can see circles of arcs (fatigue arcs) similar to shells or beaches; the instantaneous fracture zone is rough and jagged, and it is torn apart instantly when the remaining cross-section cannot withstand the final stress. When you see the shell pattern, you can basically conclude that this is a fatigue problem caused by chronic accumulation. You should check for high stress, material defects, and tooth root processing quality.
Overload fracture is caused by short-term unexpected loads: equipment jamming, foreign matter entering the meshing area, starting impact, reverse clearance return impact, or the gear has been thinned due to wear, pitting and peeling, resulting in insufficient load-bearing cross-section. The fracture surface is rough and fibrous, similar to the static bending failure fracture surface, and has no fatigue arc. There is also a type of random fracture : the fracture morphology is similar to the fatigue fracture, but the fracture location is not at the tooth root fillet section, but occurs at local stress concentrations such as material inclusions, grinding cracks, excessive residual stress or pitting pits, and the location is uncertain. For this type of broken teeth, we should focus on checking the materials and heat treatment records.
Fracture characteristics | failure mode | root cause direction |
|---|---|---|
The tooth root is broken, and the extended area is smooth with shell patterns. | Bending fatigue fracture | Stress is high for a long time: Selection is too small, overload operation, tooth root fillet is too small, surface roughness |
The fracture is rough and fibrous, with no fatigue characteristics | Broken due to overload | Material jam, blocked rotor, foreign matter entering, starting impact; or the teeth are worn and thinned |
Broken at the edge of the tooth width side rather than in the middle of the tooth root | Broken teeth due to eccentric load | Shaft bends, bearing damage, and poor alignment result in loads concentrated on approximately 10% of the tooth width. |
The fracture is smooth, crystalline, and has radial patterns. | brittle fracture | Insufficient material toughness, unqualified core hardness, or operation in low temperature environment |
The fracture location is uncertain and not at the tooth root. | Random fracture | Inclusions, grinding cracks, harmful residual stress, hard pitting induced |
The usage of this table is to first look at "where the break is" and then "what the break looks like". If teeth are broken repeatedly at the same machine position, priority should be given to troubleshooting the unbalanced load: check the contact spots of the paired gears. If the contact spots only occupy a small section of the tooth width, the problem lies in the shaft system and installation, not the gear itself.
The most common low-level mistake is to only calculate the nameplate torque Selection based on the rated power of the motor, without multiplying the service factor of the reducer , or taking 1.0~1.25 based on stable operating conditions despite knowing that there is an impact. Generally, the value should be 1.25~1.50 for medium impact conditions, 1.75~2.50 for heavy load impact, and corrections should be superimposed on continuous operation for 24 hours a day. Ignoring the efficiency loss of the multi-stage transmission will also cause an underestimate of the torque - the mechanical efficiency of the two-stage transmission is about 0.90, and the output torque is lower than the theoretical value on the motor side. Selection The margin is not enough, the bending stress of the tooth root is close to the fatigue limit for a long time, and it is only a matter of time before the tooth breaks.
For equipment such as crushers, feeders, and centrifuges, the instantaneous torque generated by material jamming and stalling can reach 2 to 4 times the rated value, far exceeding the allowable impact torque of the gear. For equipment that frequently rotates forward and reverse, additional consideration should be given to the impact of reverse clearance and return. In this type of working condition, it is not necessarily economical to simply increase the service coefficient. A torque limiter, safety coupling or frequency converter torque limiter should be used to cut off the peak value. The details of the specific device have been specifically discussed in the article "How to configure the overload protection of the reducer". Here is just a reminder: If the time point in the broken tooth record always corresponds to material blockage or emergency stop, the root cause is 90% on the load side rather than the gear side.
The surface hardness of the gears of the hardened surface reducer can reach 58~62 HRC after carburizing and quenching, but what really determines the ability to resist tooth fracture is the toughness of the core and the depth of the hardened layer: the depth of the hardened layer is generally 0.15~0.2 times the modulus. Insufficient layer depth will cause cracks at the interface between the hardened layer and the core; if the toughness of the core is poor, the instantaneous fracture zone will appear as a brittle crystalline fracture. In addition, the tooth root transition fillet radius is too small, the tooth root surface roughness is high, and micro-cracks caused by grinding burns during gear grinding will significantly reduce the tooth root fatigue strength. Common improvement methods in the industry include increasing the tooth root fillet, shot peening the tooth root (residual compressive stress can increase the bending fatigue strength by 15% to 25%), and controlling the grinding process to avoid burns.
Poor alignment, improper bearing clearance, and cantilever load at the output end exceeding the allowable value will all cause the meshing load to be biased towards the tooth width end. The judgment method is to look at the position of the broken tooth and the contact spots of the paired gears: the contact in the tooth length direction should not be less than 60%, and the tooth height direction should not be less than 45%. If the spot is at one end, repair the shaft system and bearings first, and then talk about changing the gears. When the cantilever load exceeds the standard, the manufacturer"s allowable radial force curve should be checked, and if necessary, a structure with auxiliary supports or double output bearings should be used.
Even if the single tooth is broken, it is not recommended to continue running even if it still appears to be running - the debris has entered the oil pool. Checking the abnormal noise of the reducer and the concentration of metal particles in the oil can quickly confirm secondary damage. There are three rules for handling: first, in principle, broken tooth gears are replaced with matching gears . The tooth surface wear status of the old and new gears is inconsistent. Direct mixing of the new gears will quickly wear the new gears; second, failure identification (fracture photos, hardness retest, metallography when necessary) must be done before replacement, otherwise the root cause will not be eliminated and replacement will occur; third, in terms of repair methods, grinding and modification can be considered for local chipping of soft tooth surface gears, while on-site repair welding is not recommended for hard tooth surface gears, and the properties of the carburized layer cannot be restored after repair welding. The repair boundaries of reducer maintenance are detailed in the article 'Repair Boundaries of Reducer Maintenance' and can be implemented accordingly. After replacing parts, conduct a no-load test run for 30 minutes, with the temperature rise not exceeding 40 K, and then load in stages to recheck the contact spots.
link | action | Judgment reference |
|---|---|---|
Selection | Take the sufficient service factor according to the working conditions and recalculate the peak torque. | Medium impact fs≥1.5, strong impact fs≥2.0; allowable impact torque for locked-rotor verification |
Incoming goods acceptance | Check the material list, hardness report and tooth surface accuracy grade | Tooth surface 58~62 HRC, center 30~45 HRC, accuracy not less than grade 8 of GB/T 10095.1 |
Install | Laser centering, re-tightening of anchors, and confirmation of contact spots | Rigid coupling alignment ≤ 0.02 mm; spot tooth width ≥ 60%, tooth height ≥ 45% |
Operation monitoring | Trend comparison of vibration measuring points and preliminary judgment of meshing frequency sidebands | Vibration speed warning 4.5 mm/s, shutdown 7.1 mm/s; increased sidebands indicate abnormal tooth surface |
Oil management | Regular oil drain visual inspection + magnetic plug inspection for iron filings | If shiny flakes appear, stop the machine, unpack and inspect the tooth surface. |
Part exchange strategy | Key machines are equipped with complete sets or gear pairs according to the reserve quota. | Machines with high shutdown losses are always equipped with paired gear pairs to shorten production resumption time. |
The cost of this set of actions is much lower than one downtime for broken teeth. Especially for the vibration trend, energy changes in the meshing frequency and its sidebands often appear weeks to months earlier than the broken tooth itself, which is a cost-effective early warning method.
Broken gear teeth are never just a problem with the gear itself - Selection margin, load characteristics, material technology, and installation status. One of the four links is always under pressure. Incorporate the fracture identification table and root cause list into the fault handling process, and achieve 'fracture evidence and root cause closure' every time a tooth is broken, and the recurrence rate of similar faults will be significantly reduced. If you are with repeated broken teeth , please contact looking for a root cause diagnosis or replacement solution for a reducer Hangzhou Weigao Transmission : We provide free calibration services for cycloid pinwheels, hardened cylindrical gears, worm gears and other series of reducers . We can review the service factor, cantilever load and thermal power according to your actual working conditions, and provide a complete supply plan for the complete hardened reducer machine and gear pair. Welcome to consult our reducer manufacturer technical team.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?