Author: Site Editor Publish Time: 25-10-2026 Origin: Site
Among reducer gear failures, pitting corrosion and gluing are the two most easily confused types of damage, but they have completely different causes. Reducer gear pitting is contact fatigue, and its development is measured in months or years; tooth surface gluing is the metal adhesion and tearing off after the oil film breaks, and it may only take a few hours from occurrence to scrapping. Distinguish between the two clearly and directly determine the maintenance decision: most pitting corrosion can be monitored and continued to be used, while gluing often requires immediate shutdown.
The mechanism of pitting corrosion is the initiation of fatigue cracks on the tooth surface under alternating contact stress. The pitting gradually expands from the size of the needle tip, which is a progressive damage. When the rotation speed and load remain unchanged, the service life can be estimated according to the fatigue curve. The mechanism of gluing is that the instantaneous temperature in the meshing area is too high or the oil film strength is insufficient. Solid-phase welding occurs on the two tooth surfaces. When the gear continues to rotate, the sticking point is torn apart, forming a tear groove along the sliding direction. This is not fatigue, but lubrication failure. Therefore , it has nothing to do with the running time and is strongly related to the working conditions, oil quality and oil temperature.。
discriminant dimension | Pitting corrosion | glued |
|---|---|---|
Damage location | Mainly near the node line (sliding speed is small) | Tooth top and root (high sliding speed), pitch lines are usually intact |
Appearance | Smooth shell-like pits with clear edges | Grooves and tears along the sliding direction, visible material transfer |
Development speed | Months to years, can be monitored | It can last from a few minutes to a few hours. |
oil signal | Large particles slowly increase | Sudden increase in iron content and large particles |
Tips for quick on-site judgment: if the pit is on the pitch line and the pit wall is smooth, it is pitting corrosion; if the damage is on the top and root of the tooth, there are scratches and chips, it is glue. If in doubt, take a photo of the tooth surface and keep an oil sample for subsequent judgment during reducer maintenance .
The first is thermal bonding: under high-speed and heavy-load conditions, the flash temperature exceeds the critical temperature of the oil film, which is common in the meshing area between the pinion tooth root and the large gear tooth top of the hard-tooth surface reducer. The second is cold gluing: the oil film is too thin when the speed is high and the oil viscosity is low, especially during the running-in period of new equipment. The third is lubrication management errors: wrong oil ( worm gear reducer misuses ordinary gear oil), insufficient oil volume, oil temperature exceeding 80°C for a long time, and failure to change the oil on schedule after the extreme pressure additive is exhausted.
measure | Specific practices |
|---|---|
Choose the right oil | For heavy loads, choose gear oil containing sulfur and phosphorus extreme pressure agents to allow the reducer lubricant to form a sufficient oil film thickness; for the worm gear pair, choose an oil-based worm gear oil; check the viscosity grade according to the instructions |
Control oil temperature | The temperature of the oil pool should be stable within 80°C. If it exceeds the limit, check the oil level, heat sink and ventilation cap, and install a fan if necessary. |
Standard running-in | After the machine is new or overhauled, run it at half load for about 10 hours to allow the tooth surface to run in to produce a smooth contact zone, and then run it at full load. |
Surfaces and Geometry | Gear grinding reduces roughness, tooth profile modification improves bite impact, and nitriding treatment is optional during reshaping to improve anti-gluing ability. |
Slight gluing (shallow scratches, no peeling) can be used to grind burrs, clean and change oil, and then reduce load and observe; when pieces of material transfer or deep tears occur, the tooth surface cannot be repaired. The gear pair should be replaced and the oil and heat dissipation root causes should be investigated to avoid the same damage in new parts.
Hangzhou Weigao Transmission produces a series of such as hard tooth surfaces, cycloid pinwheels, worm gears, etc. reducers and gear reduction motors It supports free calculation of oil viscosity and thermal power according to working conditions, helping customers avoid pitting corrosion and gluing risks from the source. If you are looking for a reliable reducer manufacturer , or need reducer Selection consultation and failure analysis support, please contact our technical team to obtain Selection solutions.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?