WeiGao Transmission
Email: sales@wgt.net.cn
Language
通栏图2
tonglantu.jpg
Home / News / How to determine the lubrication method and lubricant type of reducer: oil bath splash, forced oil injection and oil immersion depth standards - Hangzhou Weigao Transmission

How to determine the lubrication method and lubricant type of reducer: oil bath splash, forced oil injection and oil immersion depth standards - Hangzhou Weigao Transmission

Author: Site Editor     Publish Time: 21-10-2026      Origin: Site

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

How to determine the lubrication method and oil product of the reducer: oil bath splash, forced oil injection lubrication and lubricant model selection

The lubrication method used for a reducer is not determined by the manufacturer's habits, but is determined by the three conditions of gear circumferential speed, load power and installation form. If the lubrication method is selected incorrectly, it can cause the oil to heat up and the oil temperature to exceed the standard, or to cause tooth surface gluing and bearing ablation. The type of reducer lubricating oil should also be determined according to the lubrication method and peripheral speed. This article explains the judgment criteria, oil immersion depth, fuel injection parameters and oil viscosity one by one for on-site inspection and maintenance reference.

1. Calculate the circular speed first: the starting point for all judgments

The gear circumferential speed is calculated according to the following formula (d is the diameter of the graduation circle, in mm; n is the gear speed, in r/min):

v = π × d × n / 60000 (m/s)

For example, if the low-speed large gear of a hard-tooth surface reducer has d = 240 mm and the rotation speed is 58 r/min, then v ≈ 0.73 m/s, which is a typical low-speed oil bath working condition; if the high-speed small gear d = 50 mm and n = 1440 r/min, then v ≈ 3.8 m/s. The general judgment line in the industry is: oil bath splash lubrication is used for peripheral speeds below 12~15 m/s, and forced oil injection lubrication must be used above . For soft tooth surface, large module, and stable working conditions, the upper limit is 15 m/s; for hard tooth surface and continuous long-cycle operation, it is recommended to close the mouth at 12 m/s to avoid excessive oil churning loss and heating of the reducer.。

2. Comparison of four reducer lubrication methods

Lubrication method

Applicable peripheral speed

Typical models

Features and Key Points

Oil bath splash lubrication

v ≤ 12~15 m/s

Small and medium-sized hard tooth surface/soft tooth surface cylindrical gear reducer, cycloid pinwheel reducer, bottom worm gear reducer

Simple structure, no need for pump station; oil level must be strictly controlled, vertically installed upper bearing is prone to oil shortage, and oil replenishment measures are required

Forced circulation oil injection lubrication

v > 15 m/s or heavy load impact

Large hard tooth surface reducer, metallurgical mining wind power gearbox, high power planetary gearbox

Oil pump 0.05~0.3 MPa oil injection, lubrication + heat dissipation synchronization; equipped with filter and cooler, the oil temperature can be controlled within 80℃

Oil mist/oil air lubrication

v > 30 m/s ultra high speed

High-speed precision planetary reducer, test bench gearbox

Compressed air carries trace amounts of oil droplets, has low fuel consumption and small temperature rise; the oil mist type has fugitive pollution and is less used.

Grease lubrication

v ≤ 2 m/s intermittent operation

Low speed and high torque intermittent equipment, valve actuators

Maintenance-free and no oil leakage, but poor heat dissipation, not suitable for heavy-duty and high-temperature applications

There is another type of heavy-load correction: even if the peripheral speed does not exceed 15 m/s, the single machine power is greater than 75 kW, and there are frequent forward and reverse rotations or alternating impact conditions, it is recommended to upgrade to forced circulation injection and use a continuous supply of fresh extreme pressure oil to maintain the oil film strength.

3. Oil immersion depth and refueling amount for oil bath lubrication

The most common problem in oil bath lubrication is improper oil level: if the oil level is too high, oil churning loss will be large, the temperature will rise abnormally, and it is easy to leak from the oil seal; if the oil level is too low, the oil supply will be insufficient. Reference standards:

  • The oil immersion depth of cylindrical gears generally does not exceed one tooth height and is not less than 10 mm. The common control value is that the large gear is immersed in 1/3~1/2 tooth height;

  • Bevel gears should be immersed to the full tooth width, at least half of the tooth width;

  • When the worm is lowered, the oil level is immersed in the worm tooth height, but does not exceed the lowest ball center of the bearing; the worm gear is immersed in about one tooth height;

  • When the low-speed stage of the multi-stage transmission is immersed in oil and the high-speed stage is out of reach, use an oil tanker or oil splasher to bring the oil to the tooth surface;

  • Estimation of refueling amount: A single-stage transmission requires approximately 0.35~0.7 L of oil for each 1 kW of power transmitted. Multi-stage transmission is multiplied by the number of stages, and is ultimately determined by the oil level mirror - for details, please refer to the article Oil Filling Specifications for Reducer Refueling Amount .

There is also a layout experience for worm gear reducers: when the peripheral speed of the worm is below 4~5 m/s, it should be placed lower, and when it exceeds 5 m/s, it should be placed upward to reduce oil churning and heat generation.

4. Key parameters of forced injection lubrication

The oil supply pressure for oil injection lubrication is about 0.05~0.3 MPa, and the nozzles are evenly distributed along the tooth width and aligned with the meshing inlet. When v ≤ 25 m/s, the nozzle can be set on the meshing edge or meshing edge; when v > 25 m/s, the nozzle should be sprayed to the meshing edge, and the high-temperature tooth surface that has just meshed should be cooled first and then lubricated. The system must be equipped with a filter (the oil cleanliness is recommended to be no less than NAS level 8) and a cooler. During operation, the three parameters of oil pressure, oil temperature, and oil level are monitored, and the oil temperature is controlled within 80°C. Bearings also rely on this set of oil circuits, or rely on splash oil supply - only when the peripheral speed of the oil-immersed gear reaches 1.5~2 m/s or above can splash lubrication of the bearings be reliable. When the speed is insufficient, an oil delivery channel must be opened on the joint surface of the box to introduce oil.

5. Reducer lubricating oil model and oil change interval

The oil viscosity is selected according to the high-speed peripheral speed: v ≤ 2.5 m/s, select load extreme pressure gear oil VG320 (L-CKC 320); v > 2.5 m/s or choose VG220 for circulating oil injection lubrication. The worm gear reducer is selected according to the tooth surface sliding speed: VS ≤ 2 m/s, choose VG680, VS > 2 m/s, choose VG220, the viscosity increases by about 30% when the worm is placed upward. High-speed fuel injection conditions can be reduced to VG46~68 and synthetic oil is preferred. In terms of oil change period, under normal operating conditions, the oil should be changed every 4,000 to 5,000 hours of operation (about half a year). When the environment is harsh and dusty and humid, the oil change period can be shortened to 2,000 hours. For large centralized lubrication systems, it is recommended to change oil according to quality and regularly detect viscosity, acid value, moisture and insoluble matter. After changing the oil, perform a test run to observe the oil level and temperature rise, and include the inspection in the daily reducer maintenance list.

SelectionConsult with lubrication solutions

Lubrication method and oil selection are only part of the application of reducer. If you are making a complete machine plan for conveying, mixing, extrusion, lifting and other working conditions, and need to verify the speed ratio, torque, thermal power and reducer lubrication method , please contact Hangzhou Weigao Transmission . We provide a complete product line of cycloidal pinwheel reducers, hard-tooth surface cylindrical gear reducers, worm gear reducers, gear reduction motors, etc. Engineers can provide free Selection plans based on your motor power, speed and load parameters; as a reducer manufacturer and Hangzhou reducer manufacturer , we also provide model comparison, drawings and quotation support. You are welcome to initiate a reducer Selection consultation at any time。

Latest News

WeiGao Transmission

Weigao Gear Reducer is an alliance group company that integrates research and development, production, sales, and service

+86 400 801 9158

Email: sales@wgt.net.cn;wgt.net.cn@gmail.com
Tel:+86571 85023000

WEIGAO REDUCER

FEEDBACK