Author: Site Editor Publish Time: 23-10-2026 Origin: Site
1. Damage determination before repair
Slight wear: The amount of wear is ≤0.5mm, only shallow scratches on the bearing position and sealing position, no deformation cracks
Moderate wear: The wear amount is 0.5~2mm, the keyway roller key and the journal are partially strained, and the shaft body has no obvious deformation.
Severe damage: wear amount >2mm, shaft bending deformation, micro cracks or complete breakage, need to be returned to the factory for processing
Second and third level repair practical plan
1. Emergency temporary repair (downtime ≤8h, short-term transition of 1~3 months)
Slight wear of the bearing/seal position: After polishing and removing oil and rust, apply epoxy repair agent with wear-resistant filler, press and shape the original bearing, cure at room temperature for 2 to 4 hours, trim the edges and then assemble.
Keyway rolling key: repair welding 1~2 layers of thin welding layer on the groove wall (control heat to prevent shaft deformation), grind it smooth and use it temporarily with thickened special-shaped flat key
Damage to the shaft end thread: Use a tap of corresponding specifications to re-tap, and use a thickened anaerobic adhesive lock nut
2. Routine repair on site (1~2 days, can be used for a long time)
Bearing position/seal position wear: Use polymer composite materials to repair, grind the shaft surface and then apply the material, and use a mold to press it to restore the standard shaft diameter. After curing, the accuracy can reach H7, which can meet the heavy load conditions of hard tooth surfaces.
Moderate keyway wear: Use the keyway displacement method to re-mill the standard keyway at the 90°/180° position of the original keyway to avoid the original stress concentration area. The strength is much higher than repair welding.
Electroplating repair: Brush hard chromium plating on the worn shaft surface to restore the original fit size. The hardness of the coating can reach more than HRC50, adapting to the journal wear scenario of ≤1mm.
3. Severe damage must be returned to the factory for permanent repair
Shaft body fracture: The fractured end surface is processed flat, and a U-shaped welding groove is opened (rounded transitions are made at each part to prevent stress concentration). After preheating, argon arc welding is used to make the base and structural steel electrode is filled. After welding, it is covered with asbestos for heat preservation and slowly cooled. Finally, the shaft diameter is finely trimmed on a lathe and dynamic balance is checked.
Deformation/Cracks: Directly replace the original 40Cr quenched and tempered output shaft to ensure that the shaft diameter tolerance, bearing coaxiality, and keyway accuracy fully meet the ZDY250 original technical requirements to avoid the risk of secondary shaft breakage.
3. Key points for assembly and acceptance after repair
Thoroughly clean the shaft surface and box body before assembly. It is strictly forbidden to leave iron filings, welding slag and other impurities behind.
The bearing press-fitting adopts the hot-fitting method (oil temperature ≤120℃). It is prohibited to directly hit the shaft body with a hammer to ensure that the inner ring of the bearing and the shaft shoulder are completely fit.
The output shaft is aligned with the load coupling, the radial deviation is ≤0.03mm, the angular deviation is ≤0.05mm/m, eliminating additional bending moments.
Run without load for 1 to 2 hours, monitor the shaft temperature ≤70°C, and there is no abnormal noise or vibration, and then gradually load after confirming that the seal has no leakage.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?