Author: Site Editor Publish Time: 21-10-2026 Origin: Site
When making most engineers reducers, only check the mechanical power and speed ratio, but ignore that the ratings on the samples are given according to the basic working conditions - ambient temperature 20°C (European samples are often rated as 40°C), altitude not exceeding 1000 m, good indoor ventilation, and continuous operation. Once the on-site environment deviates from these conditions and the heat dissipation capacity of the reducer decreases, the problem of 'always overheating even though the power is sufficient' will occur. This is also the most easily ignored This article explains how environmental factors enter the calculation of Selection and how to obtain various correction coefficients.cause of on-site reducer heating .
The allowable thermal power Pt given in the reducer sample is measured under reference heat dissipation conditions. When the environmental conditions are different, should be checked as follows the thermal power of the reducer :
Pct = P2 × KT × KW × Kalt ≤ Pt
In the formula, P2 is the working machine power, KT is the ambient temperature coefficient, KW is the operating cycle coefficient, and Kalt is the altitude coefficient. If any of the three coefficients deviates from the benchmark, the calculated thermal power will increase; if the allowable thermal power is exceeded, it is necessary to increase the frame size, replace high thermal conductivity oil, or add auxiliary heat dissipation, instead of relying on "re-observation".
The ambient temperature directly affects the oil temperature and heat dissipation temperature difference. Refer to the commonly used values of European samples (based on S1 continuous operation):
maximum ambient temperature | 10℃ | 20℃ | 30℃ | 40℃ | 50℃ |
|---|---|---|---|---|---|
KT (continuous operation S1) | 1.50 | 1.32 | 1.18 | 1.00 | 0.80 |
It can be seen that when the ambient temperature rises from 40℃ to 50℃, the allowable thermal power is reduced by about 20%. Industry practice is: for every 5°C increase in ambient temperature above 40°C, the thermal power will be reduced by about 5% to 8%. The supporting gear reduction motor shall be calibrated with a 3% derating for every 5°C increase. In outdoor exposure situations, the additional temperature rise of the box from sunlight radiation shall also be taken into account. Metallurgical reducers close to the furnace body and heat pipes shall be valued based on the local ambient temperature rather than the average workshop temperature. Don't be careless on the low-temperature side: when the temperature is lower than -10°C, the viscosity of ordinary gear oil increases sharply and the oil supply is insufficient at cold start. Low-temperature special oil should be used instead. The low-temperature oil selection requirements of the reducer lubricating oil model should be determined together with the low-temperature oil selection requirements of the reducer lubricating oil model. If necessary, preheat and no-load start.
As altitude increases, air density decreases and heat dissipation becomes worse. It is estimated that the air density drops by about 11% for every 1000 m of altitude, and the air-cooling heat dissipation efficiency decreases by 20% to 25%. The common industry practice is to reduce the thermal power by 5% to 10% for every 1000 m of altitude. Commonly used classifications for reference samples:
altitude | ≤1000m | 1000~2000m | 2000~3000m | 3000~4000m | ≥4000 m |
|---|---|---|---|---|---|
Kalt | 1.00 | 0.95 | 0.90 | 0.85 | 0.80 |
Under high-altitude working conditions, in addition to the reducer body, attention should also be paid to the winding temperature rise and insulation margin on the motor side; when variable frequency drive is used, the self-fan cooling capacity of the low-speed section is further reduced, and needs to be reviewed together with the work system correction.
In places where the relative humidity is greater than 90% for a long time (such as food cleaning areas and outdoors during the rainy season in the south), it is recommended to reserve 5% to 8% power margin when Selection, and simultaneously increase the motor protection level to IP65 and above; in dusty environments, choose a model with positive pressure or dust-proof respirator to avoid clogging of the vent plug, causing the internal pressure of the box to rise and oil seepage; in corrosive gas environments, the oil seal material and box surface treatment need to be strengthened. Although these measures do not directly change the thermal power formula, they determine the sealing and lubrication reliability of the reducer in long-term operation, and should be determined at the planning stage together with the reducer maintenance cycle.
The standard checking sequence is: first select the mechanical power according to the working condition coefficient (PC = P2 × KSF ≤ PN), then check the thermal power (Pct ≤ Pt), and finally check the shaft extension radial load and peak torque. When the thermal power is not satisfied, the processing sequence is: increase the frame size by one gear → switch to synthetic oil to lower the oil temperature → add cooling ribs or forced fans → install an oil cooler. After installation, the oil temperature and bearing temperature should be measured under full load and compared with the environmental correction expectations. The temperature measurement points should be included in daily inspections to verify whether Selection has sufficient margin.
Environmental correction is only one part of the reducer system. The complete system also needs to determine the speed ratio, service factor, thermal power, cantilever load and installation method. If you are working in special working conditions such as high-temperature workshops, plateau power stations, and hot and humid outdoors Selection, please contact Hangzhou Weigao Transmission . We provide a complete product line of cycloidal pinwheel reducers, hard-tooth surface cylindrical gear reducers, worm gear reducers, gear reduction motors, etc. As a reducer manufacturer and a Hangzhou reducer manufacturer , engineers can provide free solutions based on your ambient temperature, altitude and load parameters . You are also welcome to submit parameters and obtain a quotation through online reducer consultation at any time.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?