Author: Site Editor Publish Time: 16-10-2026 Origin: Site
1. Preparation before test
Equipment and data verification: Confirm the nameplate parameters (7.5kW, 4-pole motor, speed ratio 17.25), collect historical operating records, clean the oil stains on the box, and record the ambient temperature.
Instrument Selection calibration: Equipped with a torque speed sensor with an accuracy of ±0.2% FS, a power analyzer, as well as an infrared thermometer and a vibration meter. All instruments have been calibrated in advance.
Installation and safety confirmation: Fix the reducer on the test bench, connect the input end to the 7.5kW drive motor, and the output end to the magnetic powder/eddy current loading device, correct the coupling coaxiality to ≤0.05mm, and complete the safety isolation of power outage and tagout.
Lubrication status confirmation: Add the designated brand of industrial gear oil, control the oil level at the center line of the sight glass, and keep the breather unobstructed.
2. No-load energy efficiency pre-test
Run at 30%, 50%, and 80% of the rated speed for 10 minutes each. If there is no abnormality, increase to the rated speed and run continuously for 2 hours.
Record data every 20 minutes: no-load power, input and output speed, oil pool temperature, bearing seat temperature, vibration speed effective value.
Qualification judgment: The oil temperature is stable at 40~55℃, the high-speed shaft bearing temperature is ≤90℃, the vibration speed is ≤4.5mm/s, and there is no sticking, abnormal noise or oil leakage.
3. Actual measurement of graded load energy efficiency
After the no-load is passed, it is loaded step by step, reaching 25%, 50%, 75%, and 100% of the rated load in sequence, and each working condition runs stably for 30 minutes.
The input power, output power, input torque, and output torque under each working condition are collected simultaneously, and the energy efficiency value is calculated through the formula transmission efficiency η = output power ÷ input power × 100%.
Under rated load, the transmission efficiency of this R series hard tooth surface reducer should be ≥90%, and the efficiency fluctuation at each load point should not exceed ±2%.
4. Thermal balance and energy efficiency verification
Continuously operate at 100% rated load, and monitor the oil pool temperature every 10 minutes until the temperature difference of three consecutive measurements is ≤1°C to determine thermal balance.
Record the final thermal balance oil temperature, which requires the oil temperature to be ≤80°C, the temperature rise of the bearing seat (the difference between the temperature of the bearing and the environment) to be ≤40°C, and no local hot spots.
Correct energy efficiency results based on temperature rise data: If the oil temperature exceeds the standard, abnormal lubrication loss needs to be checked, and the efficiency value must be remeasured to eliminate invalid data.
5. Test closing and data archiving
After unloading and shutting down, recheck the tooth surface contact spots and sealing status to confirm that no component damage was caused by the testing process.
Organize the original data of all working conditions, generate energy efficiency test reports, mark key background information such as ambient temperature, loading method, instrument accuracy, etc., and keep them for long-term archiving.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?