Author: Site Editor Publish Time: 23-10-2026 Origin: Site
Many purchasers first select power and speed ratio when selecting gear reduction motors , but ignore another key parameter on the nameplate - the number of poles. For the same 4kW motor, the 4-pole rated speed is about 1440r/min, and the 6-pole rated speed is only about 960r/min. Once the input speed changes, the calculation results of the speed ratio of the reducer , the force on the gear, and the life of the entire unit will also change. If the number of poles is not selected appropriately, the speed ratio will not reach the standard gear and the transmission chain will suffer an extra level of loss. The low speed and large speed ratio will be hard towed and the unit will become more heated. This article explains the differences between 2, 4, 6 and 8 poles and the matching rules with reducers at once.
The number of poles of the motor specifies the number of magnetic poles formed after the sub-winding is energized. The magnetic poles always appear in pairs of N and S, so the number of poles is an even number. The relationship between the number of poles and the speed is determined by the formula: synchronous speed n₀ = 60f/p (f is the power frequency, my country"s power frequency is 50Hz; p is the number of magnetic pole pairs, that is, the number of poles ÷ 2). The actual speed of the asynchronous motor is slightly lower than the synchronous speed, and the slip rate is usually 2% to 5%.
Number of poles | Synchronous speed (50Hz) | Rated speed (approx.) | Features and common uses |
|---|---|---|---|
2 poles | 3000 r/min | 2800~2900 r/min | With high speed, small size and low torque, it is mostly used in direct drive applications such as fans and water pumps. |
4 poles | 1500 r/min | 1400~1450 r/min | The efficiency and power factor are balanced, the supporting reducer has a wide range of applications, and the market has sufficient stock. |
6 poles | 1000 r/min | 960~970 r/min | Smooth at low speed, low noise and vibration, suitable for medium and low speed high torque transmission |
8 poles | 750 r/min | 720~730 r/min | Large starting torque, suitable for heavy-duty low-speed working conditions such as crushing and mixing |
It is easy to find the number of poles by looking at the nameplate: around 1430r/min rated speed is 4 poles, around 960r/min is 6 poles, and around 720r/min is 8 poles.
When the power is fixed, the speed and torque have a 'seesaw' relationship (P = T×n/9550): the more poles and the lower the speed, the greater the rated torque at the same power. Empirical data is that the torque of a 6-pole motor is about 50% higher than that of a 4-pole motor, and that of an 8-pole motor is about 100% higher than that of a 4-pole motor. The price is size and weight: at the same power, a 2-pole motor is 30%~50% smaller and 20%~40% lighter than an 8-pole motor. When the installation space is tight, pay attention to changes in the size of the machine base. In terms of efficiency, 2-pole and 4-pole motors have more mature designs and better loss balance; when the number of poles is too high, iron losses and copper losses increase, light-load efficiency decreases, and the power factor of 8-pole motors is low, and reactive power compensation may be required in high-power applications. In addition, high-pole-count motors have large starting torque and smoother operation. This feature can be used to reduce the impact on the reducer when starting directly with heavy loads .
Once the number of poles is determined, the speed ratio calculation of the reducer is i = motor rated speed ÷ output speed, and then move closer to the standard speed ratio. It is a common practice in the industry to select the number of poles in three gears according to the output speed of the load end:
Load output speed | Recommended number of poles | Collocation ideas and examples |
|---|---|---|
50 r/min or more | 4 poles (1440 r/min) | Moderate speed ratio (about i≤29 to 50r/min), high efficiency, short delivery time, versatile for general conveying and packaging lines |
10~50 r/min | 6 poles (960 r/min) | Reduce speed ratio requirements: target 30r/min, 4 poles require i=48, 6 poles only need i=32, one less transmission level, and the transmission efficiency of the reducer is higher |
Below 10 r/min | 8-pole (720 r/min) or two-stage/worm gear options | Avoid hard towing with extremely large speed ratio in 4-pole configuration: when i>100, the temperature rise of the unit exceeds the standard and the gear wear accelerates. |
For example: the equipment requires 30r/min and 5.5kW. If it is equipped with a 4-pole motor, i=1440÷30=48, the standard speed ratio is 47 or 50; if it is equipped with a 6-pole motor, i=960÷30=32, which falls exactly within the standard gear of single-stage or two-stage helical gears, with fewer gear stages and less meshing loss. Conversely, when matching the motor power with the reducer, attention should also be paid: after replacing the motor with a higher number of poles, the input speed will decrease, and the output speed will become lower at the same speed ratio. The output torque should be recalculated according to T₂=9550×P×i×η/n₁, and do not continue to use the old parameters.
Misunderstanding 1: If the speed ratio is not enough, go for the bigger one. The 4-pole motor is equipped with an ultra-large speed ratio reducer with i>100, which is a high-frequency item that causes heat in the reducer . The correct approach is to increase the number of poles or change to a double-stage or worm gear scheme. Misunderstanding 2: Only look at power but not speed. Replacing 4 poles with 6 poles with the same power, the input torque is amplified by nearly 50%, and the calibration of the input end of the reducer and the first gear must be redone. Misunderstanding 3: The number of poles is ignored in frequency conversion working conditions. The self-heat dissipation capacity of the low-speed section decreases during variable frequency operation. Choosing a 6-pole or 8-pole low-speed motor can reduce the long-term operation time in the low-frequency section and is more friendly to temperature rise.
Checklist before placing an order: ① Clarify the output speed and torque; ② Determine the number of poles according to the gearing table; ③ Calculate the reducer speed ratio and take the value to the standard gear to avoid non-standard values; ④ Check the rated torque, thermal power and shaft extension cantilever load of the reducer; ⑤ Confirm the low-speed heat dissipation and insulation level when driving with variable frequency.
The reasonable sequence for gear reduction motor Selection is: first determine the number of motor poles according to the output speed and working conditions, and then calculate the speed ratio and check the torque and thermal power, so that each parameter falls in the standard gear. If the number of poles is selected correctly, the reducer will have one less transmission stage and the gear will bear less force, which will benefit the efficiency, noise and life of the unit.
Hangzhou Weigao Transmission Machinery Co., Ltd. provides R/S/K/F hard tooth surface series, cycloid pinwheels, worm gears, planets and other reducers and complete gear reduction motors . It can recommend combinations of 4-pole, 6-pole and 8-pole motors and reducers according to working conditions. As a reducer manufacturer , we provide free Selection and technical evaluation: report the power, output speed, load type and installation size, and you can get pole number matching and model recommendations. If you need reducer Selection consultation , please contact Hangzhou Weigao Transmission, a reducer manufacturer in Hangzhou. We support customization of drawings and samples and complete machine supply.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?