WeiGao Transmission
Email: sales@wgt.net.cn
Language
通栏图2
tonglantu.jpg
Home / News / How to choose a vertical mixing reducer: axial load, thrust bearing and lubrication seal configuration - Hangzhou Weigao Transmission

How to choose a vertical mixing reducer: axial load, thrust bearing and lubrication seal configuration - Hangzhou Weigao Transmission

Author: Site Editor     Publish Time: 19-10-2026      Origin: Site

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

How to choose a mixer reducer: axial load, thrust bearing and lubrication seal configuration under vertical working conditions

Most mixer reducers are installed vertically, with the output shaft facing downwards and directly flanged to the top of the mixing tank. This is completely different from the horizontal conveying and lifting conditions: the self-weight of the mixing paddle, the self-weight of the shaft system and the reaction force of the material will all press on the output bearing of the reducer in the form of axial force. If you still only match the motor power and speed ratio at Selection, problems such as early bearing failure, worm gear axial movement, and output leakage will easily occur later. This article explains the calibration method of vertical from three dimensions: stress analysis, load-bearing calibration, and lubrication and sealing reducer Selection .

1. Three special forces in vertical mixing conditions

Compared with horizontal transmission, vertical mixing arrangements require additional attention to three types of loads:

  • Axial cantilever load : The self-weight of the blade, the self-weight of the mixing shaft and the material thrust jointly act on the output shaft to form a continuous downward axial force; under high-viscosity material conditions, the material reaction force will further amplify this value. This is a typical reducer cantilever load problem, which directly determines the life of the output bearing;

  • Pulsating torque : The liquid resistance is not constant. During the startup and stirring process of high-viscosity or solid-liquid mixture materials, the torque fluctuation can reach 1.5~2 times of the rated value. Selection must be calibrated according to the peak torque, not the average torque;

  • Lateral shaking : Unbalanced blades or material disturbance during long-axis mixing will transmit vibration through the shaft system, increasing the radial load of the reducer . Models with too small bearing spacing are prone to shaft system oscillation and oil seal eccentric wear.

2. Load check: How to determine thrust bearing and torque margin

The allowable axial thrust of the output shaft of a standard vertical model is usually in the range of 10 to 50 kN. Heavy-duty chemical mixing requires a customized enlarged bearing seat or an independent thrust bearing. The following methods can be used for verification: first calculate all the axial forces of the mixing shaft system and leave a margin according to the manufacturer"s allowable thrust table; the output end bearings should be tapered roller bearings or angular contact ball bearings that can withstand composite loads; the axial movement should be controlled within 0.05~0.15 mm. If it exceeds the limit, it means that the bearing preload is insufficient or worn. In terms of torque, the actual stirring torque of high-viscosity materials is usually 1.3~1.5 times the theoretical value. It is recommended to leave a safety margin of 1.5 times for normal working conditions and 2 times for heavy-load and frequent start-stop conditions. Please refer to the table below for model selection:

model

Transmission efficiency

Suitable for mixing conditions

Helical gear/bevel gear reducer

94%~96%

Low viscosity medium, medium and high speed, continuous operation

Worm gear reducer

50%~80%

Intermittent operation, low speed and low power; continuous operation prone to heat generation

Cycloidal pinwheel reducer (BLD vertical)

Single level ≥90%, two levels ≥85%

Low speed and high torque, heavy load impact, reactor and sludge mixing

Among them, the multi-tooth meshing structure of the cycloidal pinwheel reducer allows short-term overloading. The single-stage speed ratio is 9 to 87, and the two-stage speed ratio can reach 121 to 5133. One stage can cover the low speed commonly used in reactors, and is a common choice for vertical mixing configurations. However, the efficiency of the worm gear model is low, and heat is obvious during low-speed continuous operation. Thermal power must be calculated when Selection to avoid oil temperature exceeding the limit.

3. Lubrication and sealing configuration for vertical installation

In a vertical arrangement, lubricating oil accumulates toward the bottom of the box due to gravity, and the upper gears and bearings are prone to insufficient lubrication. This is also a common cause of oil leakage and failure of reducers. Attention should be paid to the configuration: fill the oil according to the vertical oil level scale, and do not copy the horizontal oil level; the oil viscosity can be one level higher than the horizontal oil level (such as VG220 Use VG320 instead, choose VG460/VG680 for heavy loads); the output shaft end adopts a combined structure of double-lip fluorine rubber oil seal and dust seal, and an oil drain cavity is reserved between the two seals; the breathing valve should be installed sideways to prevent the positive pressure in the box from pressing the oil out of the shaft seal; the roughness of the shaft seal mating surface is controlled within Ra0.8 μm to avoid grinding grooves to form leakage channels.

4. Installation accuracy and daily maintenance points

The flatness of the mounting flange surface should not exceed 0.05 mm/m, and the bolts should be tightened evenly 2 to 3 times in diagonal order to avoid flange deformation and eccentric wear of the oil seal. Daily reducer maintenance : Change the lubricating oil when the new machine is running for about 200 hours for the first time, and change the oil regularly thereafter. Check the oil level and oil seal status every six months; different brands of lubricating oil cannot be mixed; pay attention to the blade balance. Blade deformation will transmit vibration back to the reducer through the stirring shaft, accelerating bearing wear.

If you need to match a vertical transmission solution for mixing equipment, please contact Hangzhou Weigao Transmission . As a reducer manufacturer, we provide a series of vertical mixer reducers and gear reduction motors such as cycloidal pinwheels, hard tooth surfaces, worm gears, etc. We support customization of non-standard flanges, special shaft extensions and explosion-proof configurations, and provide free reducer Selection consultation : The technical team of Hangzhou reducer manufacturer can complete a complete check of axial load and torque according to your medium viscosity, paddle type and shaft system size.

Latest News

WeiGao Transmission

Weigao Gear Reducer is an alliance group company that integrates research and development, production, sales, and service

+86 400 801 9158

Email: sales@wgt.net.cn;wgt.net.cn@gmail.com
Tel:+86571 85023000

WEIGAO REDUCER

FEEDBACK