WeiGao Transmission
Email: sales@wgt.net.cn
Language
通栏图2
tonglantu.jpg
Home / News / How to choose a hard-tooth surface reducer: load-bearing advantages, five-step calculation method and working condition coefficient value - Hangzhou Weigao Transmission

How to choose a hard-tooth surface reducer: load-bearing advantages, five-step calculation method and working condition coefficient value - Hangzhou Weigao Transmission

Author: Site Editor     Publish Time: 22-10-2026      Origin: Site

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

How to choose a hard-tooth surface reducer: first find out where its load-bearing advantage comes from

In continuous heavy-load situations such as mining crushing, metallurgical steel rolling, and port transportation, hard-toothed surface reducers are almost unavoidable models: the gears are carburized and quenched, and the tooth surface hardness reaches HRC58~62. The tooth shape is then modified by precision grinding to form a 'hard on the outside and tough on the inside' structural characteristics. Compared with quenched and tempered soft tooth surface gears, the load-bearing capacity is about 30% to 50% higher under the same volume conditions, the single-stage transmission efficiency can reach 95% to 98%, and the design life under normal maintenance is generally 10 to 15 years. The cost is that the process is complicated and the purchase cost is 50% to 80% higher than that of the soft tooth surface model. Therefore , when using the reducer , it is necessary to use it on the cutting edge, and to avoid the waste of 'small horse-drawn cart' style or 'large machine base with low load' style. This guide to hardened cylindrical gear reducers Selection explains the performance boundaries, five-step calculation method and working condition coefficient values ​​at once.

Performance boundaries: Which working conditions are suitable for hard tooth surfaces and which ones do not need to be hardened?

The advantages of hard-tooth surface models are heavy load, impact, and continuous operation, but they are not required in all situations. According to the load characteristics, make a preliminary judgment based on the following table:

Working condition type

Typical equipment

Is it recommended to harden the tooth surface?

Strong impact, continuous 24h operation

Crusher, metallurgical rolling mill, grinding mill

It is recommended to focus on checking the peak torque and thermal power.

Medium impact, long time operation

Conveyor reducer , mixing host, elevator

Recommendation, taking into account noise and lifespan

Smooth, intermittent operation

Packaging machines, small feeders, valve drives

Optional soft tooth surface or worm gear models to control costs

High-precision positioning

Servo feed, robot axis

Choose precision planetary or servo reducer instead

When port cranes, concrete mixing main engines, and high-power fans and water pumps operate at full load for a long time, hard-tooth surface models can significantly reduce the frequency of downtime and maintenance; choosing them for light-load intermittent operation will cause waste of costs. This is an account that must be settled before Selection.

Five-step method for calculating reducer Selection: from speed ratio to shaft extension load

Referring to the general selection method of DBY, DCY, TH, TB and other series of samples, it is recommended to follow five steps for hard tooth surface reducer Selection:

The first step is to calculate the transmission ratio. i=n₁/n₂, determined by the motor speed and the working machine speed, move to the nearest standard speed ratio of the sample; if the deviation is too large, adjust the peripheral pulley and sprocket transmission ratio or change the number of motor poles.

The second step is to select the specifications according to the rated power. It satisfies PN≥Pe·KA·KE, where Pe is the working machine power, KA is the working condition coefficient, and KE is the reliability coefficient (for continuous production lines with high reliability requirements, KE is recommended to be 1.2~1.5).

The third step is to check the starting torque. Calculate according to MK·n₁/(PN·9550)≤2.5, where MK is the starting or maximum input torque; in the case of frequent forward and reverse rotation and load starting, the sample allowable impact torque must also be checked.

The fourth step is to check the thermal power. The strength of the gear determines 'whether it can be driven', and the thermal power check of the reducer determines 'whether it can be driven and driven'. Without auxiliary cooling, Pct=P2·KT·KW·KP≤PT should be satisfied, where KT, KW, and KP are the ambient temperature, operating cycle and power utilization coefficient respectively; if not satisfied, increase the center distance by one gear, or install heat dissipation ribs, cooling fans, and oil coolers.

The fifth step is to check the shaft extension radial load. The pulleys, sprockets, and gears on the output shaft will produce additional bending moments. The actual radial force must not exceed the sample allowable value, and the closer the action point is to the outside of the shaft end, the smaller the allowable value is. It needs to be reduced according to the sample formula; if it exceeds the standard, enlarge the machine base or customize a reinforced bearing plan.

How to obtain the working condition coefficient and reducer service coefficient

The rated power of the sample is measured under steady load and standard environment. The actual Selection must be converted with the working condition coefficient, which is commonly referred to as the service coefficient of the reducer :

Load type

Typical equipment

Coefficient value

steady load

Conveyor lines, fans, packaging machines

1.2~1.5

medium impact

Chemical mixing, conventional lifting, machine tool feeding

1.5~2.0

strong impact

Crusher, rolling mill, heavy duty lifting

2.0~3.0

Then add the work system correction: continuous operation for 24 hours a day, more than 5 to 10 starts and stops per hour, internal combustion engine dragging, etc., the coefficient will be increased. On the other hand, it is not right to use a large coefficient as "insurance" - if the machine base is larger, the cost and inertia will increase, and starting will be more difficult. A reasonable approach is to try to get the actual measured load torque curve and compare the peak torque with the allowable value.

Five common Selection misunderstandings, self-examination one by one

First, only look at the power but not the torque: the reducer is a torque amplifier. Sufficient input power does not mean that the output torque meets the load. The rated output torque and the actual load torque must be checked. The second is to ignore the working condition coefficient: if the impact load is based on the steady load Selection, the reducer gear pitting will quickly appear on the tooth surface and the service life will be reduced in half. The third is continuous operation without calibrating the thermal power: the lubricating oil will fail after the oil temperature exceeds the limit, and wear, oil leakage, and seal aging will follow one after another. The fourth is to ignore the radial load: the radial force of the belt and sprocket drive is a common cause of early damage to the output bearing. Fifth, the interfaces are not checked: the input shaft bore diameter, keyway, and motor flange must match the on-site motor, otherwise installation will not be possible and rework costs will be high.

Hard tooth surface reducerSelectionSuggestion: Explain the parameters clearly before determining the model

To sum up, the key to the hard-tooth surface reducer Selection is not to duplicate the sample and model, but to first spread out the five working conditions of load characteristics, working system, start and stop frequency, environmental conditions, and installation methods, and then calculate them one by one according to the five steps of speed ratio, rated power, starting torque, thermal power, and radial load. As Hangzhou Weigao Transmission a reducer manufacturer , has a complete product line of hardened cylindrical gears, cycloid pinwheels, worm gears, gear reduction motors, etc., and can issue Selection plans based on on-site working conditions. If you are doing reducer consultation , please contact this Hangzhou reducer manufacturer : provide the motor power, speed and load parameters, and you can get a complete calculation and quotation for free. Special working conditions support customization with drawings and samples.

Latest News

WeiGao Transmission

Weigao Gear Reducer is an alliance group company that integrates research and development, production, sales, and service

+86 400 801 9158

Email: sales@wgt.net.cn;wgt.net.cn@gmail.com
Tel:+86571 85023000

WEIGAO REDUCER

FEEDBACK