Author: Site Editor Publish Time: 20-10-2026 Origin: Site
1. Initial appearance inspection (screening immediately after welding)
1. Visual + magnifying glass inspection: Confirm that the weld is evenly formed, without cracks, pores, undercuts, lack of fusion and other surface defects, and there is no spatter or welding flash residue in the welding area.
2. Weld size verification: Measure with a weld inspection ruler. The weld reinforcement is controlled at 1~3mm, and the transition with the base metal is smooth without sharp edges and corners.
3. Tapping inspection: Use a pointed hammer to tap the periphery of the weld, and use the sound to determine whether there is incomplete welding or internal looseness and abnormal noise.
2. Non-destructive testing (core defect inspection)
1. Magnetic particle testing (MT)
Clean the weld and the surrounding 50mm range to Sa2 level cleanliness. Use the AC yoke method to bidirectionally magnetize the weld longitudinally and circumferentially. After spraying magnetic suspension, observe the magnetic traces and judge according to the JB/T 6063-2007 standard: Linear defects with a length > 2mm or dense point defects are directly judged to be unqualified. After the inspection is completed, the workpiece needs to be demagnetized.
2. Ultrasonic flaw detection (UT)
Select the 2.0~2.5MHz, K1~K2 oblique probe, use the standard test block of the same material to calibrate the sensitivity, use the single pulse reflection method to scan the entire area of the weld, and check for internal pores, slag inclusions, lack of fusion, internal cracks and other defects. If the bottom wave is significantly reduced and accompanied by clutter, it is a serious internal defect.
3. Mechanical property verification
1. Hardness test: Take 3 measuring points each at the center of the weld, the fusion line, the heat-affected zone (2~5mm away from the fusion line), and the base metal area. The hardness of the heat-affected zone shall not exceed 120% of the base material. The conventional qualified value is ≤280HV. If the local hardness exceeds 300HV, additional stress relief annealing is required.
2. Stress release verification: Confirm that the welding stress has been released by tapping with a light hammer after each welding pass to avoid residual stress causing subsequent delayed cracking.
4. Retest of shape and position accuracy
In a constant temperature environment of 20±1°C, use a three-dimensional coordinate measuring instrument to scan the key mounting surfaces, bearing locations, and connection hole locations of the machine base:
The deviation of flatness, parallelism and coaxiality is ≤0.03mm/m, and the deformation of the positioning reference shall not exceed ±0.05mm to ensure that subsequent assembly accuracy reaches the standard.
5. Operation performance verification
1. No-load test machine: After assembly, run continuously in forward and reverse directions for 2 to 4 hours. Monitor the machine base vibration value ≤ 4.5mm/s, the bearing temperature rise does not exceed 35°C, and there is no abnormal impact noise.
2. Rated load verification: Load in four levels: 25%, 50%, 75%, and 100%. Run at full load until the oil temperature stabilizes. Confirm that there is no leakage in the weld, no recurrence of cracks, and the overall operating status meets the design requirements.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?