Author: Site Editor Publish Time: 21-10-2026 Origin: Site
1. Safety tips before adjustment
It is strictly forbidden to dismantle the original structure of new equipment at will. Before on-site adjustment, the power must be cut off, the lubricating oil in the box must be drained, and the original marks of the shaft end and meshing position must be made.
When the radial clearance exceeds 0.25mm after the bearing is worn, replace the bearing directly with a new one without any adjustment.
2. Clearance standard reference
According to JB/T9051 industry standard, the axial clearance of TP series bearings must meet the following range:
3. Step-by-step adjustment operation
1. Worm shaft bearing clearance adjustment
The worm shaft mostly adopts the structure of "double tapered roller bearings fixed face to face + cylindrical roller bearing at the other end swimming". First assemble the worm shaft in place, use a depth gauge to measure the depth difference from the end surface of the bearing outer ring to the joint surface of the end cover, and calculate the total thickness of the required gasket.
Add a flat grinding adjustment shim between the bearing end cover and the box joint surface, gradually increase or decrease the thickness of the shim, and manually turn the worm while adjusting until the worm rotates flexibly without stuck or obvious axial movement.
Use a feeler gauge to retest the fit between the bearing end face and the shaft shoulder. The 0.02mm feeler gauge must not be inserted to ensure that the bearing is completely close to the positioning surface.
2. Worm gear shaft bearing clearance adjustment
Both ends of the worm gear are tapered roller bearings. Coarse adjustment is made through a round nut with a locking screw at the end of the shaft. Turn the nut to move the worm gear axially. Turn the output shaft to confirm that there is no jamming in the rotation.
Use the lead pressing method to measure the thickness of the flattened lead wire between the bearing outer ring and the end cover, accurately calculate the remaining clearance, supplement the adjustment shims with corresponding thickness, and finally tighten the locking screw and lock nut to prevent loosening during operation.
3. Engagement linkage verification
Apply red red powder evenly on the tooth surface of the worm gear, manually turn the worm to drive the worm wheel to rotate, and observe the contact spots. Normal spots should be distributed in the middle of the tooth surface, slightly toward the direction of the worm rotation. The contact area accounts for ≥60% of the tooth length and ≥50% of the tooth height.
If the spots are offset, fine-tune the axial position of the worm or worm gear, and simultaneously correct the bearing clearances on both sides to avoid excessive meshing load due to excessive clearance on one side.
4. Final verification and confirmation
After the adjustment is completed, push and pull the worm and worm gear shaft axially. The measured axial movement must fall within the standard range. The entire shaft system must be rotated for more than 3 turns, and there shall be no jamming or abnormal noise throughout the process.
Run forward and reverse without load for 2 hours, and the temperature rise of the bearing shall not exceed 30°C. After the oil temperature is stable, the remaining clearance in the hot state shall be measured again and shall not be less than 60% of the lower limit of the cold state standard to avoid locking due to thermal expansion.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?